# Invocation command line: # /home/cpu2k17/bin/harness/runcpu --configfile amd_rate_aocc500_znver5_A1.cfg --tune all --reportable --iterations 3 --nopower --runmode rate --tune base:peak --size test:train:refrate fprate # output_root was not used for this run ############################################################################ ################################################################################ # AMD AOCC 500 SPEC CPU 2017 V1.1.9 Rate Configuration File for 64-bit Linux # # File name : amd_rate_aocc500_znver5_A1.cfg # Creation Date : September 12, 2024 # CPU 2017 Version : 1.1.9 # Supported benchmarks : All Rate benchmarks (intrate, fprate) # Compiler name/version : AOCC 5.0.0 # Operating system version : RHEL 8.6 # Supported OS's : SLE 15 SP6, Ubuntu 22.04-24.04, RHEL 9.x, RHEL 8.6 # Hardware : AMD Turin (AMD64) # FP Base Pointer Size : 64-bit # FP Peak Pointer Size : 64-bit # INT Base Pointer Size : 64-bit # INT Peak Pointer Size : 32/64-bit # Auto Parallelization : No # # Note: DO NOT EDIT THIS FILE, the only edits required to properly run these # binaries are made in the ini Python file. Please consult Readme.amd_rate_aocc500_znver5_A1.txt # for a few uncommon exceptions which require edits to this file. # # Description: # # This binary package automates away many of the complexities necessary to set # up and run SPEC CPU 2017 under optimized conditions on AMD Turin-based # server platforms within Linux (AMD64). # # The binary package was built specifically for AMD Turin microprocessors and # is not intended to run on other products. # # Please install the binary package by following the instructions in # "Readme.amd_rate_aocc500_znver5_A1.txt" under the "How To Use the Binaries" section. # # The binary package is designed to work without alteration on two socket AMD # Turin-based servers with 96 cores per socket, SMT enabled and 1.5 TiB of DDR5 # memory distributed evenly among all 24 channels using 64 GiB DIMMs. # # To run the binary package on other Turin configurations, please review # "Readme.amd_rate_aocc500_znver5_A1.txt". In general, Turin CPUs # should be autodetected with no action required by the user. # # In most cases, it should be unnecessary to edit "amd_rate_aocc500_znver5_A1.cfg" or any # other file besides "ini_amd_rate_aocc500_znver5_A1.py" where reporting fields # and run conditions are set. # # The run script automatically sets the optimal number of rate copies and binds # them appropriately. # # The run script and accompanying binary package are designed to work on Ubuntu # 22.04-24.04, SLE 15 SP6, RHEL 9.x, RHEL 8.6. # # Important! If you write your own run script, please set the stack size to # "unlimited" when executing this binary package. Failure to do so may cause # some benchmarks to overflow the stack. For example, to set stack size within # the bash shell, include the following line somewhere at the top of your run # script before the runcpu invocation: # # ulimit -s unlimited # # Modification of this config file should only be necessary if you intend to # rebuild the binaries. General instructions for rebuilding the binaries are # found in-line below. # ################################################################################ # Modifiable macros: ################################################################################ # "allow_build"" switch: # Change the following line to true if you intend to REBUILD the binaries (AMD # does not support this). Valid values are "true" or "false" (no quotes). %define allow_build false # Only change these macros if you are rebuilding the binary package: %define compiler_name aocc500 %define binary_package_name amd_rate_%{compiler_name}_znver5_A %define binary_package_ext %{binary_package_name} %define binary_package_revision 1 %define build_path /home/work/cpu2017/v119/aocc5/1316 %define flags_file_name %{compiler_name}-flags-A1.xml # Do NOT change build_lib_dir after the build or it will trigger a # rebuild of the xalanc. It should also remain literal: %define build_lib_dir %{binary_package_name}_lib # To enable the platform file, be sure to uncomment the flagsurl02 header line # below in the Header settings. %define platform_file_name INVALID_platform_%{binary_package_name}.xml ################################################################################ # You should never have to change binary_package_full_name: %define binary_package_full_name %{binary_package_name}%{binary_package_revision} ################################################################################ # Include file names ################################################################################ # The include file contains fields that are commonly changed. This file is auto- # generated based upon INI file settings and should not need user modification # for runs. The flags include file contains all of the compiler flags. %define inc_file_name %{binary_package_full_name}.inc %define flags_inc_file_name %{binary_package_full_name}_flags.inc %define port_flags_inc_file_name %{binary_package_full_name}_flags_portability.inc %define workaround_flags_inc_file_name %{binary_package_full_name}_flags_workaround.inc # Binary label extension: # Only modify the binary label extension if you plan to rebuild the binaries. # If you plan to recompile these CPU 2017 binaries, please choose a new extension # name below to avoid confusion with the current binary set on your system # under test, and to avoid confusion for SPEC submission reviewers. You will # also need to set "allow_build" to true above. Finally, you must modify the # Paths section below to point to your library locations if the paths are not # already set up in your build environment. # Note that AMD calls an external script to set up the compiler and library # paths before initiating the build. %define ext %{binary_package_ext} ################################################################################ # Paths and Environment Variables # ** MODIFY AS NEEDED (modification should not be necessary for runs) ** ################################################################################ # Allow environment variables to be set before runs: preenv = 1 # Necessary to avoid out-of-memory exceptions on certain SUTs: preENV_MALLOC_CONF = retain:true # Define the name of the directory that holds AMD library files: %define lib_dir %{binary_package_name}_lib # Set the shared object library path for runs and builds: preENV_LD_LIBRARY_PATH = $[top]/%{lib_dir}/lib:$[top]/%{lib_dir}/lib32:%{ENV_LD_LIBRARY_PATH} # Define 32-bit library build paths: # Do NOT use $[top] with the 32-bit libraries because doing so will cause an # options checksum error triggering a xalanc recompile attempt on SUTs having # different file paths. # Do NOT change build_lib_dir after the build or it will also trigger a # rebuild of the xalanc: AMDALLOC_LIB32_PATH = %{build_path}/%{build_lib_dir}/lib32 %if '%{allow_build}' eq 'false' # The include file is only needed for runs, but not for builds. # include: %{inc_file_name} # ----- Begin inclusion of 'amd_rate_aocc500_znver5_A1.inc' ############################################################################ ################################################################################ ################################################################################ # File name: amd_rate_aocc500_znver5_A1.inc # File generation code date: September 23, 2022 # File generation date/time: September 20, 2024 / 14:22:22 # # This file is automatically generated during a SPEC CPU2017 run. # # To modify inc file generation, please consult the readme file or the run # script. ################################################################################ ################################################################################ ################################################################################ ################################################################################ # The following macros are generated for use in the cfg file. ################################################################################ ################################################################################ %define logical_core_count 128 %define physical_core_count 64 ################################################################################ # The following inc blocks set the rate copy counts and affinity settings. # # intrate benchmarks: 500.perlbench_r,502.gcc_r,505.mcf_r,520.omnetpp_r, # 523.xalancbmk_r,525.x264_r,531.deepsjeng_r,541.leela_r,548.exchange2_r, # 557.xz_r # fpspeed benchmarks: 503.bwaves_r,507.cactuBSSN_r,519.lbm_r,521.wrf_r, # 527.cam4_r,538.imagick_r,544.nab_r,549.fotonik3d_r,554.roms_r # # Selected copy counts from '8534p' section of CPU info ################################################################################ # default copy counts: default: copies = 128 # Bind commands for assigning affinity: bind0 = numactl --localalloc --physcpubind=0 bind1 = numactl --localalloc --physcpubind=1 bind2 = numactl --localalloc --physcpubind=2 bind3 = numactl --localalloc --physcpubind=3 bind4 = numactl --localalloc --physcpubind=4 bind5 = numactl --localalloc --physcpubind=5 bind6 = numactl --localalloc --physcpubind=6 bind7 = numactl --localalloc --physcpubind=7 bind8 = numactl --localalloc --physcpubind=8 bind9 = numactl --localalloc --physcpubind=9 bind10 = numactl --localalloc --physcpubind=10 bind11 = numactl --localalloc --physcpubind=11 bind12 = numactl --localalloc --physcpubind=12 bind13 = numactl --localalloc --physcpubind=13 bind14 = numactl --localalloc --physcpubind=14 bind15 = numactl --localalloc --physcpubind=15 bind16 = numactl --localalloc --physcpubind=16 bind17 = numactl --localalloc --physcpubind=17 bind18 = numactl --localalloc --physcpubind=18 bind19 = numactl --localalloc --physcpubind=19 bind20 = numactl --localalloc --physcpubind=20 bind21 = numactl --localalloc --physcpubind=21 bind22 = numactl --localalloc --physcpubind=22 bind23 = numactl --localalloc --physcpubind=23 bind24 = numactl --localalloc --physcpubind=24 bind25 = numactl --localalloc --physcpubind=25 bind26 = numactl --localalloc --physcpubind=26 bind27 = numactl --localalloc --physcpubind=27 bind28 = numactl --localalloc --physcpubind=28 bind29 = numactl --localalloc --physcpubind=29 bind30 = numactl --localalloc --physcpubind=30 bind31 = numactl --localalloc --physcpubind=31 bind32 = numactl --localalloc --physcpubind=32 bind33 = numactl --localalloc --physcpubind=33 bind34 = numactl --localalloc --physcpubind=34 bind35 = numactl --localalloc --physcpubind=35 bind36 = numactl --localalloc --physcpubind=36 bind37 = numactl --localalloc --physcpubind=37 bind38 = numactl --localalloc --physcpubind=38 bind39 = numactl --localalloc --physcpubind=39 bind40 = numactl --localalloc --physcpubind=40 bind41 = numactl --localalloc --physcpubind=41 bind42 = numactl --localalloc --physcpubind=42 bind43 = numactl --localalloc --physcpubind=43 bind44 = numactl --localalloc --physcpubind=44 bind45 = numactl --localalloc --physcpubind=45 bind46 = numactl --localalloc --physcpubind=46 bind47 = numactl --localalloc --physcpubind=47 bind48 = numactl --localalloc --physcpubind=48 bind49 = numactl --localalloc --physcpubind=49 bind50 = numactl --localalloc --physcpubind=50 bind51 = numactl --localalloc --physcpubind=51 bind52 = numactl --localalloc --physcpubind=52 bind53 = numactl --localalloc --physcpubind=53 bind54 = numactl --localalloc --physcpubind=54 bind55 = numactl --localalloc --physcpubind=55 bind56 = numactl --localalloc --physcpubind=56 bind57 = numactl --localalloc --physcpubind=57 bind58 = numactl --localalloc --physcpubind=58 bind59 = numactl --localalloc --physcpubind=59 bind60 = numactl --localalloc --physcpubind=60 bind61 = numactl --localalloc --physcpubind=61 bind62 = numactl --localalloc --physcpubind=62 bind63 = numactl --localalloc --physcpubind=63 bind64 = numactl --localalloc --physcpubind=64 bind65 = numactl --localalloc --physcpubind=65 bind66 = numactl --localalloc --physcpubind=66 bind67 = numactl --localalloc --physcpubind=67 bind68 = numactl --localalloc --physcpubind=68 bind69 = numactl --localalloc --physcpubind=69 bind70 = numactl --localalloc --physcpubind=70 bind71 = numactl --localalloc --physcpubind=71 bind72 = numactl --localalloc --physcpubind=72 bind73 = numactl --localalloc --physcpubind=73 bind74 = numactl --localalloc --physcpubind=74 bind75 = numactl --localalloc --physcpubind=75 bind76 = numactl --localalloc --physcpubind=76 bind77 = numactl --localalloc --physcpubind=77 bind78 = numactl --localalloc --physcpubind=78 bind79 = numactl --localalloc --physcpubind=79 bind80 = numactl --localalloc --physcpubind=80 bind81 = numactl --localalloc --physcpubind=81 bind82 = numactl --localalloc --physcpubind=82 bind83 = numactl --localalloc --physcpubind=83 bind84 = numactl --localalloc --physcpubind=84 bind85 = numactl --localalloc --physcpubind=85 bind86 = numactl --localalloc --physcpubind=86 bind87 = numactl --localalloc --physcpubind=87 bind88 = numactl --localalloc --physcpubind=88 bind89 = numactl --localalloc --physcpubind=89 bind90 = numactl --localalloc --physcpubind=90 bind91 = numactl --localalloc --physcpubind=91 bind92 = numactl --localalloc --physcpubind=92 bind93 = numactl --localalloc --physcpubind=93 bind94 = numactl --localalloc --physcpubind=94 bind95 = numactl --localalloc --physcpubind=95 bind96 = numactl --localalloc --physcpubind=96 bind97 = numactl --localalloc --physcpubind=97 bind98 = numactl --localalloc --physcpubind=98 bind99 = numactl --localalloc --physcpubind=99 bind100 = numactl --localalloc --physcpubind=100 bind101 = numactl --localalloc --physcpubind=101 bind102 = numactl --localalloc --physcpubind=102 bind103 = numactl --localalloc --physcpubind=103 bind104 = numactl --localalloc --physcpubind=104 bind105 = numactl --localalloc --physcpubind=105 bind106 = numactl --localalloc --physcpubind=106 bind107 = numactl --localalloc --physcpubind=107 bind108 = numactl --localalloc --physcpubind=108 bind109 = numactl --localalloc --physcpubind=109 bind110 = numactl --localalloc --physcpubind=110 bind111 = numactl --localalloc --physcpubind=111 bind112 = numactl --localalloc --physcpubind=112 bind113 = numactl --localalloc --physcpubind=113 bind114 = numactl --localalloc --physcpubind=114 bind115 = numactl --localalloc --physcpubind=115 bind116 = numactl --localalloc --physcpubind=116 bind117 = numactl --localalloc --physcpubind=117 bind118 = numactl --localalloc --physcpubind=118 bind119 = numactl --localalloc --physcpubind=119 bind120 = numactl --localalloc --physcpubind=120 bind121 = numactl --localalloc --physcpubind=121 bind122 = numactl --localalloc --physcpubind=122 bind123 = numactl --localalloc --physcpubind=123 bind124 = numactl --localalloc --physcpubind=124 bind125 = numactl --localalloc --physcpubind=125 bind126 = numactl --localalloc --physcpubind=126 bind127 = numactl --localalloc --physcpubind=127 submit = echo "$command" > run.sh ; $BIND bash run.sh ################################################################################ ################################################################################ # fprate copy counts: fprate: copies = 64 # Bind commands for assigning affinity: bind0 = numactl --localalloc --physcpubind=0 bind1 = numactl --localalloc --physcpubind=1 bind2 = numactl --localalloc --physcpubind=2 bind3 = numactl --localalloc --physcpubind=3 bind4 = numactl --localalloc --physcpubind=4 bind5 = numactl --localalloc --physcpubind=5 bind6 = numactl --localalloc --physcpubind=6 bind7 = numactl --localalloc --physcpubind=7 bind8 = numactl --localalloc --physcpubind=8 bind9 = numactl --localalloc --physcpubind=9 bind10 = numactl --localalloc --physcpubind=10 bind11 = numactl --localalloc --physcpubind=11 bind12 = numactl --localalloc --physcpubind=12 bind13 = numactl --localalloc --physcpubind=13 bind14 = numactl --localalloc --physcpubind=14 bind15 = numactl --localalloc --physcpubind=15 bind16 = numactl --localalloc --physcpubind=16 bind17 = numactl --localalloc --physcpubind=17 bind18 = numactl --localalloc --physcpubind=18 bind19 = numactl --localalloc --physcpubind=19 bind20 = numactl --localalloc --physcpubind=20 bind21 = numactl --localalloc --physcpubind=21 bind22 = numactl --localalloc --physcpubind=22 bind23 = numactl --localalloc --physcpubind=23 bind24 = numactl --localalloc --physcpubind=24 bind25 = numactl --localalloc --physcpubind=25 bind26 = numactl --localalloc --physcpubind=26 bind27 = numactl --localalloc --physcpubind=27 bind28 = numactl --localalloc --physcpubind=28 bind29 = numactl --localalloc --physcpubind=29 bind30 = numactl --localalloc --physcpubind=30 bind31 = numactl --localalloc --physcpubind=31 bind32 = numactl --localalloc --physcpubind=32 bind33 = numactl --localalloc --physcpubind=33 bind34 = numactl --localalloc --physcpubind=34 bind35 = numactl --localalloc --physcpubind=35 bind36 = numactl --localalloc --physcpubind=36 bind37 = numactl --localalloc --physcpubind=37 bind38 = numactl --localalloc --physcpubind=38 bind39 = numactl --localalloc --physcpubind=39 bind40 = numactl --localalloc --physcpubind=40 bind41 = numactl --localalloc --physcpubind=41 bind42 = numactl --localalloc --physcpubind=42 bind43 = numactl --localalloc --physcpubind=43 bind44 = numactl --localalloc --physcpubind=44 bind45 = numactl --localalloc --physcpubind=45 bind46 = numactl --localalloc --physcpubind=46 bind47 = numactl --localalloc --physcpubind=47 bind48 = numactl --localalloc --physcpubind=48 bind49 = numactl --localalloc --physcpubind=49 bind50 = numactl --localalloc --physcpubind=50 bind51 = numactl --localalloc --physcpubind=51 bind52 = numactl --localalloc --physcpubind=52 bind53 = numactl --localalloc --physcpubind=53 bind54 = numactl --localalloc --physcpubind=54 bind55 = numactl --localalloc --physcpubind=55 bind56 = numactl --localalloc --physcpubind=56 bind57 = numactl --localalloc --physcpubind=57 bind58 = numactl --localalloc --physcpubind=58 bind59 = numactl --localalloc --physcpubind=59 bind60 = numactl --localalloc --physcpubind=60 bind61 = numactl --localalloc --physcpubind=61 bind62 = numactl --localalloc --physcpubind=62 bind63 = numactl --localalloc --physcpubind=63 submit = echo "$command" > run.sh ; $BIND bash run.sh ################################################################################ ################################################################################ # peak copy counts: 128 508.namd_r,511.povray_r,526.blender_r,538.imagick_r,544.nab_r=peak: copies = 128 # Bind commands for assigning affinity: bind0 = numactl --localalloc --physcpubind=0 bind1 = numactl --localalloc --physcpubind=1 bind2 = numactl --localalloc --physcpubind=2 bind3 = numactl --localalloc --physcpubind=3 bind4 = numactl --localalloc --physcpubind=4 bind5 = numactl --localalloc --physcpubind=5 bind6 = numactl --localalloc --physcpubind=6 bind7 = numactl --localalloc --physcpubind=7 bind8 = numactl --localalloc --physcpubind=8 bind9 = numactl --localalloc --physcpubind=9 bind10 = numactl --localalloc --physcpubind=10 bind11 = numactl --localalloc --physcpubind=11 bind12 = numactl --localalloc --physcpubind=12 bind13 = numactl --localalloc --physcpubind=13 bind14 = numactl --localalloc --physcpubind=14 bind15 = numactl --localalloc --physcpubind=15 bind16 = numactl --localalloc --physcpubind=16 bind17 = numactl --localalloc --physcpubind=17 bind18 = numactl --localalloc --physcpubind=18 bind19 = numactl --localalloc --physcpubind=19 bind20 = numactl --localalloc --physcpubind=20 bind21 = numactl --localalloc --physcpubind=21 bind22 = numactl --localalloc --physcpubind=22 bind23 = numactl --localalloc --physcpubind=23 bind24 = numactl --localalloc --physcpubind=24 bind25 = numactl --localalloc --physcpubind=25 bind26 = numactl --localalloc --physcpubind=26 bind27 = numactl --localalloc --physcpubind=27 bind28 = numactl --localalloc --physcpubind=28 bind29 = numactl --localalloc --physcpubind=29 bind30 = numactl --localalloc --physcpubind=30 bind31 = numactl --localalloc --physcpubind=31 bind32 = numactl --localalloc --physcpubind=32 bind33 = numactl --localalloc --physcpubind=33 bind34 = numactl --localalloc --physcpubind=34 bind35 = numactl --localalloc --physcpubind=35 bind36 = numactl --localalloc --physcpubind=36 bind37 = numactl --localalloc --physcpubind=37 bind38 = numactl --localalloc --physcpubind=38 bind39 = numactl --localalloc --physcpubind=39 bind40 = numactl --localalloc --physcpubind=40 bind41 = numactl --localalloc --physcpubind=41 bind42 = numactl --localalloc --physcpubind=42 bind43 = numactl --localalloc --physcpubind=43 bind44 = numactl --localalloc --physcpubind=44 bind45 = numactl --localalloc --physcpubind=45 bind46 = numactl --localalloc --physcpubind=46 bind47 = numactl --localalloc --physcpubind=47 bind48 = numactl --localalloc --physcpubind=48 bind49 = numactl --localalloc --physcpubind=49 bind50 = numactl --localalloc --physcpubind=50 bind51 = numactl --localalloc --physcpubind=51 bind52 = numactl --localalloc --physcpubind=52 bind53 = numactl --localalloc --physcpubind=53 bind54 = numactl --localalloc --physcpubind=54 bind55 = numactl --localalloc --physcpubind=55 bind56 = numactl --localalloc --physcpubind=56 bind57 = numactl --localalloc --physcpubind=57 bind58 = numactl --localalloc --physcpubind=58 bind59 = numactl --localalloc --physcpubind=59 bind60 = numactl --localalloc --physcpubind=60 bind61 = numactl --localalloc --physcpubind=61 bind62 = numactl --localalloc --physcpubind=62 bind63 = numactl --localalloc --physcpubind=63 bind64 = numactl --localalloc --physcpubind=64 bind65 = numactl --localalloc --physcpubind=65 bind66 = numactl --localalloc --physcpubind=66 bind67 = numactl --localalloc --physcpubind=67 bind68 = numactl --localalloc --physcpubind=68 bind69 = numactl --localalloc --physcpubind=69 bind70 = numactl --localalloc --physcpubind=70 bind71 = numactl --localalloc --physcpubind=71 bind72 = numactl --localalloc --physcpubind=72 bind73 = numactl --localalloc --physcpubind=73 bind74 = numactl --localalloc --physcpubind=74 bind75 = numactl --localalloc --physcpubind=75 bind76 = numactl --localalloc --physcpubind=76 bind77 = numactl --localalloc --physcpubind=77 bind78 = numactl --localalloc --physcpubind=78 bind79 = numactl --localalloc --physcpubind=79 bind80 = numactl --localalloc --physcpubind=80 bind81 = numactl --localalloc --physcpubind=81 bind82 = numactl --localalloc --physcpubind=82 bind83 = numactl --localalloc --physcpubind=83 bind84 = numactl --localalloc --physcpubind=84 bind85 = numactl --localalloc --physcpubind=85 bind86 = numactl --localalloc --physcpubind=86 bind87 = numactl --localalloc --physcpubind=87 bind88 = numactl --localalloc --physcpubind=88 bind89 = numactl --localalloc --physcpubind=89 bind90 = numactl --localalloc --physcpubind=90 bind91 = numactl --localalloc --physcpubind=91 bind92 = numactl --localalloc --physcpubind=92 bind93 = numactl --localalloc --physcpubind=93 bind94 = numactl --localalloc --physcpubind=94 bind95 = numactl --localalloc --physcpubind=95 bind96 = numactl --localalloc --physcpubind=96 bind97 = numactl --localalloc --physcpubind=97 bind98 = numactl --localalloc --physcpubind=98 bind99 = numactl --localalloc --physcpubind=99 bind100 = numactl --localalloc --physcpubind=100 bind101 = numactl --localalloc --physcpubind=101 bind102 = numactl --localalloc --physcpubind=102 bind103 = numactl --localalloc --physcpubind=103 bind104 = numactl --localalloc --physcpubind=104 bind105 = numactl --localalloc --physcpubind=105 bind106 = numactl --localalloc --physcpubind=106 bind107 = numactl --localalloc --physcpubind=107 bind108 = numactl --localalloc --physcpubind=108 bind109 = numactl --localalloc --physcpubind=109 bind110 = numactl --localalloc --physcpubind=110 bind111 = numactl --localalloc --physcpubind=111 bind112 = numactl --localalloc --physcpubind=112 bind113 = numactl --localalloc --physcpubind=113 bind114 = numactl --localalloc --physcpubind=114 bind115 = numactl --localalloc --physcpubind=115 bind116 = numactl --localalloc --physcpubind=116 bind117 = numactl --localalloc --physcpubind=117 bind118 = numactl --localalloc --physcpubind=118 bind119 = numactl --localalloc --physcpubind=119 bind120 = numactl --localalloc --physcpubind=120 bind121 = numactl --localalloc --physcpubind=121 bind122 = numactl --localalloc --physcpubind=122 bind123 = numactl --localalloc --physcpubind=123 bind124 = numactl --localalloc --physcpubind=124 bind125 = numactl --localalloc --physcpubind=125 bind126 = numactl --localalloc --physcpubind=126 bind127 = numactl --localalloc --physcpubind=127 submit = echo "$command" > run.sh ; $BIND bash run.sh ################################################################################ ################################################################################ # peak copy counts: 64 507.cactuBSSN_r,519.lbm_r,527.cam4_r=peak: copies = 64 # Bind commands for assigning affinity: bind0 = numactl --localalloc --physcpubind=0 bind1 = numactl --localalloc --physcpubind=1 bind2 = numactl --localalloc --physcpubind=2 bind3 = numactl --localalloc --physcpubind=3 bind4 = numactl --localalloc --physcpubind=4 bind5 = numactl --localalloc --physcpubind=5 bind6 = numactl --localalloc --physcpubind=6 bind7 = numactl --localalloc --physcpubind=7 bind8 = numactl --localalloc --physcpubind=8 bind9 = numactl --localalloc --physcpubind=9 bind10 = numactl --localalloc --physcpubind=10 bind11 = numactl --localalloc --physcpubind=11 bind12 = numactl --localalloc --physcpubind=12 bind13 = numactl --localalloc --physcpubind=13 bind14 = numactl --localalloc --physcpubind=14 bind15 = numactl --localalloc --physcpubind=15 bind16 = numactl --localalloc --physcpubind=16 bind17 = numactl --localalloc --physcpubind=17 bind18 = numactl --localalloc --physcpubind=18 bind19 = numactl --localalloc --physcpubind=19 bind20 = numactl --localalloc --physcpubind=20 bind21 = numactl --localalloc --physcpubind=21 bind22 = numactl --localalloc --physcpubind=22 bind23 = numactl --localalloc --physcpubind=23 bind24 = numactl --localalloc --physcpubind=24 bind25 = numactl --localalloc --physcpubind=25 bind26 = numactl --localalloc --physcpubind=26 bind27 = numactl --localalloc --physcpubind=27 bind28 = numactl --localalloc --physcpubind=28 bind29 = numactl --localalloc --physcpubind=29 bind30 = numactl --localalloc --physcpubind=30 bind31 = numactl --localalloc --physcpubind=31 bind32 = numactl --localalloc --physcpubind=32 bind33 = numactl --localalloc --physcpubind=33 bind34 = numactl --localalloc --physcpubind=34 bind35 = numactl --localalloc --physcpubind=35 bind36 = numactl --localalloc --physcpubind=36 bind37 = numactl --localalloc --physcpubind=37 bind38 = numactl --localalloc --physcpubind=38 bind39 = numactl --localalloc --physcpubind=39 bind40 = numactl --localalloc --physcpubind=40 bind41 = numactl --localalloc --physcpubind=41 bind42 = numactl --localalloc --physcpubind=42 bind43 = numactl --localalloc --physcpubind=43 bind44 = numactl --localalloc --physcpubind=44 bind45 = numactl --localalloc --physcpubind=45 bind46 = numactl --localalloc --physcpubind=46 bind47 = numactl --localalloc --physcpubind=47 bind48 = numactl --localalloc --physcpubind=48 bind49 = numactl --localalloc --physcpubind=49 bind50 = numactl --localalloc --physcpubind=50 bind51 = numactl --localalloc --physcpubind=51 bind52 = numactl --localalloc --physcpubind=52 bind53 = numactl --localalloc --physcpubind=53 bind54 = numactl --localalloc --physcpubind=54 bind55 = numactl --localalloc --physcpubind=55 bind56 = numactl --localalloc --physcpubind=56 bind57 = numactl --localalloc --physcpubind=57 bind58 = numactl --localalloc --physcpubind=58 bind59 = numactl --localalloc --physcpubind=59 bind60 = numactl --localalloc --physcpubind=60 bind61 = numactl --localalloc --physcpubind=61 bind62 = numactl --localalloc --physcpubind=62 bind63 = numactl --localalloc --physcpubind=63 submit = echo "$command" > run.sh ; $BIND bash run.sh ################################################################################ ################################################################################ # peak copy counts: 32 510.parest_r,521.wrf_r,549.fotonik3d_r,554.roms_r=peak: copies = 32 # Bind commands for assigning affinity: bind0 = numactl --localalloc --physcpubind=0 bind1 = numactl --localalloc --physcpubind=2 bind2 = numactl --localalloc --physcpubind=4 bind3 = numactl --localalloc --physcpubind=6 bind4 = numactl --localalloc --physcpubind=8 bind5 = numactl --localalloc --physcpubind=10 bind6 = numactl --localalloc --physcpubind=12 bind7 = numactl --localalloc --physcpubind=14 bind8 = numactl --localalloc --physcpubind=16 bind9 = numactl --localalloc --physcpubind=18 bind10 = numactl --localalloc --physcpubind=20 bind11 = numactl --localalloc --physcpubind=22 bind12 = numactl --localalloc --physcpubind=24 bind13 = numactl --localalloc --physcpubind=26 bind14 = numactl --localalloc --physcpubind=28 bind15 = numactl --localalloc --physcpubind=30 bind16 = numactl --localalloc --physcpubind=32 bind17 = numactl --localalloc --physcpubind=34 bind18 = numactl --localalloc --physcpubind=36 bind19 = numactl --localalloc --physcpubind=38 bind20 = numactl --localalloc --physcpubind=40 bind21 = numactl --localalloc --physcpubind=42 bind22 = numactl --localalloc --physcpubind=44 bind23 = numactl --localalloc --physcpubind=46 bind24 = numactl --localalloc --physcpubind=48 bind25 = numactl --localalloc --physcpubind=50 bind26 = numactl --localalloc --physcpubind=52 bind27 = numactl --localalloc --physcpubind=54 bind28 = numactl --localalloc --physcpubind=56 bind29 = numactl --localalloc --physcpubind=58 bind30 = numactl --localalloc --physcpubind=60 bind31 = numactl --localalloc --physcpubind=62 submit = echo "$command" > run.sh ; $BIND bash run.sh ################################################################################ ################################################################################ # peak copy counts: 16 503.bwaves_r=peak: copies = 16 # Bind commands for assigning affinity: bind0 = numactl --localalloc --physcpubind=0 bind1 = numactl --localalloc --physcpubind=4 bind2 = numactl --localalloc --physcpubind=8 bind3 = numactl --localalloc --physcpubind=12 bind4 = numactl --localalloc --physcpubind=16 bind5 = numactl --localalloc --physcpubind=20 bind6 = numactl --localalloc --physcpubind=24 bind7 = numactl --localalloc --physcpubind=28 bind8 = numactl --localalloc --physcpubind=32 bind9 = numactl --localalloc --physcpubind=36 bind10 = numactl --localalloc --physcpubind=40 bind11 = numactl --localalloc --physcpubind=44 bind12 = numactl --localalloc --physcpubind=48 bind13 = numactl --localalloc --physcpubind=52 bind14 = numactl --localalloc --physcpubind=56 bind15 = numactl --localalloc --physcpubind=60 submit = echo "$command" > run.sh ; $BIND bash run.sh ################################################################################ # Switch back to the default block after the include file: default: ################################################################################ ################################################################################ ################################################################################ ################################################################################ # The remainder of this file defines CPU2017 report parameters. ################################################################################ ################################################################################ ################################################################################ # SPEC CPU 2017 report header ################################################################################ license_num =3 tester =HPE test_sponsor =HPE hw_vendor =Hewlett Packard Enterprise hw_model000 =ProLiant DL145 Gen11 hw_model001 =(2.30 GHz, AMD EPYC 8534P) #--------- If you install new compilers, edit this section -------------------- sw_compiler =C/C++/Fortran: Version 5.0.0 of AOCC ################################################################################ ################################################################################ # Hardware, firmware and software information ################################################################################ hw_avail =Oct-2024 sw_avail =Sep-2024 hw_cpu_name =AMD EPYC 8534P hw_cpu_nominal_mhz =2300 hw_cpu_max_mhz =3100 hw_ncores =64 hw_nthreadspercore =2 hw_ncpuorder =1 chip hw_other =CPU Cooling: Air fw_bios000 =HPE BIOS Version v1.20 08/09/2024 released fw_bios001 = Aug-2024 sw_base_ptrsize =64-bit hw_pcache =32 KB I + 32 KB D on chip per core hw_scache =1 MB I+D on chip per core hw_tcache000 =128 MB I+D on chip per chip, hw_tcache001 = 16 MB shared / 8 cores hw_ocache =None sw_other =None ################################################################################ # Notes ################################################################################ # Enter notes_000 through notes_100 here. notes_000 =Binaries were compiled on a system with 2x AMD EPYC 9174F CPU + 1.5TiB Memory using RHEL 8.6 notes_005 = notes_010 =NA: The test sponsor attests, as of date of publication, that CVE-2017-5754 (Meltdown) notes_015 =is mitigated in the system as tested and documented. notes_020 =Yes: The test sponsor attests, as of date of publication, that CVE-2017-5753 (Spectre variant 1) notes_025 =is mitigated in the system as tested and documented. notes_030 =Yes: The test sponsor attests, as of date of publication, that CVE-2017-5715 (Spectre variant 2) notes_035 =is mitigated in the system as tested and documented. notes_040 = notes_submit_000 ='numactl' was used to bind copies to the cores. notes_submit_005 =See the configuration file for details. notes_submit_010 = notes_os_000 ='ulimit -s unlimited' was used to set environment stack size limit notes_os_005 ='ulimit -l 2097152' was used to set environment locked pages in memory limit notes_os_010 = notes_os_015 =runcpu command invoked through numactl i.e.: notes_os_020 =numactl --interleave=all runcpu notes_os_025 = notes_os_030 =To limit dirty cache to 8% of memory, 'sysctl -w vm.dirty_ratio=8' run as root. notes_os_035 =To limit swap usage to minimum necessary, 'sysctl -w vm.swappiness=1' run as root. notes_os_040 =To free node-local memory and avoid remote memory usage, notes_os_045 ='sysctl -w vm.zone_reclaim_mode=1' run as root. notes_os_050 =To clear filesystem caches, 'sync; sysctl -w vm.drop_caches=3' run as root. notes_os_055 =To disable address space layout randomization (ASLR) to reduce run-to-run notes_os_060 =variability, 'sysctl -w kernel.randomize_va_space=0' run as root. notes_os_065 = notes_comp_000 =The AMD64 AOCC Compiler Suite is available at notes_comp_005 =http://developer.amd.com/amd-aocc/ notes_comp_010 = # notes_jemalloc_000 =jemalloc: configured and built with GCC v4.8.2 in RHEL 7.4 (No options specified) # notes_jemalloc_005 =jemalloc 5.1.0 is available here: # notes_jemalloc_010 =https://github.com/jemalloc/jemalloc/releases/download/5.1.0/jemalloc-5.1.0.tar.bz2 # notes_jemalloc_015 = # sw_other000 =jemalloc: jemalloc memory allocator library v5.1.0 ################################################################################ # The following note fields describe platorm settings. ################################################################################ # example: (edit and uncomment as necessary) # notes_plat_000 =BIOS settings: # notes_plat_002 = TDP: 400 # notes_plat_004 = Determinism Slider set to Power # notes_plat_006 = PPT: 400 # notes_plat_010 = NPS: 4 # notes_plat_011 = Workload Profile = CPU Intensive # notes_plat_012 = TSME = Disabled # notes_plat_014 = SEV Control = Disabled # notes_plat_015 = Fan Speed: Maximum ################################################################################ # The following are custom fields: ################################################################################ # Use custom_fields to enter lines that are not listed here. For example: # notes_plat_100 = Energy Bias set to Max Performance # new_field = Ambient temperature set to 10C ################################################################################ # The following fields must be set here for only Int benchmarks. ################################################################################ intrate: sw_peak_ptrsize =32/64-bit notes_os_thp_000 =To enable Transparent Hugepages (THP) only on request for base runs, notes_os_thp_001 ='echo madvise > /sys/kernel/mm/transparent_hugepage/enabled' run as root. notes_os_thp_002 =To enable THP for all allocations for peak runs, notes_os_thp_003 ='echo always > /sys/kernel/mm/transparent_hugepage/enabled' and notes_os_thp_004 ='echo always > /sys/kernel/mm/transparent_hugepage/defrag' run as root. notes_os_thp_005 = ################################################################################ # The following fields must be set here for FP benchmarks. ################################################################################ fprate: sw_peak_ptrsize =64-bit notes_os_thp_000 =To enable Transparent Hugepages (THP) for all allocations, notes_os_thp_005 ='echo always > /sys/kernel/mm/transparent_hugepage/enabled' and notes_os_thp_010 ='echo always > /sys/kernel/mm/transparent_hugepage/defrag' run as root. notes_os_thp_015 = ################################################################################ # The following fields must be set here or they will be overwritten by sysinfo. ################################################################################ intrate,fprate: hw_disk =1 x 480 GB SATA SSD hw_memory =768 GB (6 x 128 GB 4Rx4 PC5-4800B-R) hw_nchips =1 prepared_by =HPE Performance Engineering sw_file =btrfs sw_os000 =SUSE Linux Enterprise Server 15 SP6 sw_os001 =Kernel 6.4.0-150600.21-default sw_state =Run level 3 (multi-user) ################################################################################ # End of inc file ################################################################################ # Switch back to the default block after the include file: default: # ---- End inclusion of '/home/cpu2k17/config/amd_rate_aocc500_znver5_A1.inc' # Switch back to default block after the include file: default: fail_build = yes # FIX THIS SO THAT CHECKSUMS WILL BE ENFORCED! %elif '%{allow_build}' eq 'true' # If you intend to rebuild, be sure to set the library paths either in the # build script or here: preENV_LIBRARY_PATH = $[top]/%{build_lib_dir}/lib:$[top]/%{build_lib_dir}/lib32:%{ENV_LIBRARY_PATH} % define build_ncpus 64 # controls number of simultaneous compiles fail_build = 0 makeflags = --jobs=%{build_ncpus} --load-average=%{build_ncpus} %else % error The value of "allow_build" is %{allow_build}, but it can only be "true" or "false". This error was generated %endif ################################################################################ # Enable automated data collection per benchmark ################################################################################ # Data collection is not enabled for reportable runs. # teeout is necessary to get data collection stdout into the logs. Best # practices for the individual data collection items would be to have # them store important output in separate files. Filenames could be # constructed from $SPEC (environment), $lognum (result number from runcpu), # and benchmark name/number. teeout = yes # Run runcpu with '-v 35' (or greater) to log lists of variables which can # be used in substitutions as below. # For CPU2006, change $label to $ext %define data-collection-parameters benchname='$name' benchnum='$num' benchmark='$benchmark' iteration=$iter size='$size' tune='$tune' label='$label' log='$log' lognum='$lognum' from_runcpu='$from_runcpu' %define data-collection-start $[top]/data-collection/data-collection start %{data-collection-parameters} %define data-collection-stop $[top]/data-collection/data-collection stop %{data-collection-parameters} monitor_specrun_wrapper = %{data-collection-start} ; $command ; %{data-collection-stop} ################################################################################ # Header settings ################################################################################ backup_config = 0 # set to 0 if you do not want backup files bench_post_setup = sync # command_add_redirect: If set, the generated ${command} will include # redirection operators (stdout, stderr), which are passed along to the shell # that executes the command. If this variable is not set, specinvoke does the # redirection. command_add_redirect = yes env_vars = yes flagsurl000 = http://www.spec.org/cpu2017/flags/HPE-Platform-Flags-AMD-Siena-rev1.0.xml flagsurl001 = http://www.spec.org/cpu2017/flags/aocc500-flags.xml #flagsurl02 = $[top]/%{platform_file_name} # label: User defined extension string that tags your binaries & directories: label = %{ext} line_width = 1020 log_line_width = 1020 mean_anyway = yes output_format = all reportable = yes size = test,train,ref teeout = yes teerunout = yes tune = base,peak ################################################################################ # Include the flags file: ################################################################################ #include: %{flags_inc_file_name} # ----- Begin inclusion of 'amd_rate_aocc500_znver5_A1_flags.inc' ############################################################################ ################################################################################ # AMD AOCC 5.0.0 SPEC CPU2017 V1.1.9 Rate Configuration Flags for AMD64 Linux ################################################################################ # Compilers ################################################################################ default: CC = clang -m64 CXX = clang++ -m64 -std=c++14 FC = flang -m64 CLD = clang -m64 CXXLD = clang++ -m64 -std=c++14 FLD = flang -m64 CC_VERSION_OPTION = --version CXX_VERSION_OPTION = --version FC_VERSION_OPTION = --version ################################################################################ # Default libraries and variables ################################################################################ default: # Libraries: EXTRA_LIBS = -lamdalloc \ -lamdlibm \ -lm \ -ldl MATHLIBOPT = #clearing this variable or else SPEC will set it to -lm VECMATHLIB = -fveclib=AMDLIBM # Variables: OPT_ROOT = -march=znver5 \ $(VECMATHLIB) \ -ffast-math OPT_ROOT_BASE = -O3 \ $(OPT_ROOT) OPT_ROOT_PEAK = -Ofast \ $(OPT_ROOT) \ -flto ################################################################################ # Portability and workaround include files ################################################################################ # Portability flags include file: #include: %{port_flags_inc_file_name} # ----- Begin inclusion of 'amd_rate_aocc500_znver5_A1_flags_portability.inc' ############################################################################ ################################################################################ # AMD AOCC 5.0.0 SPEC CPU2017 V1.1.9 Rate Portability Flags for AMD64 Linux ################################################################################ default: # data model applies to all benchmarks EXTRA_PORTABILITY = -DSPEC_LP64 # *** Benchmark-specific portability *** # Anything other than the data model is only allowed where a need is proven. # (ordered by last 2 digits of benchmark number) 500.perlbench_r: #lang='C' PORTABILITY = -DSPEC_LINUX_X64 521.wrf_r: #lang='F,C' CPORTABILITY = -DSPEC_CASE_FLAG FPORTABILITY = -Mbyteswapio 523.xalancbmk_r: #lang='CXX' PORTABILITY = -DSPEC_LINUX 526.blender_r: #lang='CXX,C' CPORTABILITY = -funsigned-char 527.cam4_r: #lang='F,C' PORTABILITY = -DSPEC_CASE_FLAG ################################################################################ # End Portability Flags ################################################################################ # ---- End inclusion of '/home/cpu2k17/config/amd_rate_aocc500_znver5_A1_flags_portability.inc' # Workaround flags include file: #include: %{workaround_flags_inc_file_name} # ----- Begin inclusion of 'amd_rate_aocc500_znver5_A1_flags_workaround.inc' ############################################################################ ################################################################################ # AMD AOCC 5.0.0 SPEC CPU2017 V1.1.9 Rate Workaround Flags for AMD64 Linux ################################################################################ # The workarounds in this section would not qualify under the SPEC CPU # PORTABILITY rule. # - In peak, they can be set as needed for individual benchmarks. # - In base, individual settings are not allowed; set for whole suite. # Use EXTRA_CFLAGS, EXTRA_CXXFLAGS, and EXTRA_FFLAGS for them. # # See: # https://www.spec.org/cpu2017/Docs/runrules.html#portability # https://www.spec.org/cpu2017/Docs/runrules.html#BaseFlags ####################### # Default workarounds # ####################### default: # Allow unused compile/link arguments without triggering warnings during build: EXTRA_CFLAGS = -Wno-unused-command-line-argument EXTRA_CXXFLAGS = -Wno-unused-command-line-argument EXTRA_FFLAGS = -Wno-unused-command-line-argument LDOPTIONS = -Wno-unused-command-line-argument #################### # Base workarounds # #################### # # *** NONE *** # ############################## # Integer workarounds - base # ############################## # intrate=base: # The following is necessary for 502/602 gcc: EXTRA_LDFLAGS = -z muldefs ######################### # FP workarounds - base # ######################### # # *** NONE *** # #################### # Peak workarounds # #################### # # *** NONE *** # ############################## # Integer workarounds - peak # ############################## 502.gcc_r=peak: #lang='C' EXTRA_CFLAGS = -Wno-unused-command-line-argument \ -fgnu89-inline EXTRA_LDFLAGS = -z muldefs ##################################### # Floating Point workarounds - peak # ##################################### # # *** NONE *** # # ---- End inclusion of '/home/cpu2k17/config/amd_rate_aocc500_znver5_A1_flags_workaround.inc' ################################################################################ # Tuning Flags ################################################################################ ##################### # Base tuning flags # ##################### default=base: COPTIMIZE = $(OPT_ROOT_BASE) \ -fno-PIE \ -no-pie \ -flto \ -fstruct-layout=7 \ -mllvm -unroll-threshold=50 \ -mllvm -inline-threshold=1000 \ -fremap-arrays \ -fstrip-mining \ -mllvm -reduce-array-computations=3 \ -zopt CXXOPTIMIZE = $(OPT_ROOT_BASE) \ -flto \ -mllvm -unroll-threshold=100 \ -mllvm -loop-unswitch-threshold=200000 \ -mllvm -reduce-array-computations=3 \ -zopt FOPTIMIZE = $(OPT_ROOT_BASE) \ -flto \ -Mrecursive \ -funroll-loops \ -mllvm -lsr-in-nested-loop \ -mllvm -reduce-array-computations=3 \ -fepilog-vectorization-of-inductions \ -zopt LDCXXFLAGS = -Wl,-mllvm -Wl,-x86-use-vzeroupper=false \ -Wl,-mllvm -Wl,-extra-inliner LDCFLAGS = -Wl,-mllvm -Wl,-ldist-scalar-expand \ -fenable-aggressive-gather LDFLAGS = -Wl,-mllvm -Wl,-align-all-nofallthru-blocks=6 \ -Wl,-mllvm -Wl,-reduce-array-computations=3 LDFFLAGS = -Wl,-mllvm -Wl,-enable-X86-prefetching \ -Wl,-mllvm -Wl,-enable-aggressive-gather=true \ -Wl,-mllvm -Wl,-enable-masked-gather-sequence=false # Libraries: EXTRA_LIBS = -lamdlibm \ -lm \ -lamdalloc \ -lflang \ -ldl EXTRA_FLIBS = # Don't put the AMD and mvec math libraries in MATH_LIBS because it will trigger a reporting issue # because GCC won't use them. Forcefeed all benchmarks the math libraries in EXTRA_LIBS and clear # out MATH_LIBS. MATH_LIBS = ######################## # intrate tuning flags # ######################## intrate: FOPTIMIZE = $(OPT_ROOT_BASE) \ -flto \ -fepilog-vectorization-of-inductions \ -mllvm -optimize-strided-mem-cost \ -floop-transform \ -mllvm -unroll-aggressive \ -mllvm -unroll-threshold=500 EXTRA_CXXOPTIMIZE = -fno-PIE \ -no-pie \ -fvirtual-function-elimination \ -fvisibility=hidden \ -mllvm -do-block-reorder=advanced LDCFLAGS = -Wl,-mllvm -Wl,-ldist-scalar-expand \ -fenable-aggressive-gather \ -Wl,-mllvm -Wl,-extra-inliner LDCXXFLAGS = -Wl,-mllvm -Wl,-do-block-reorder=advanced LDFFLAGS = -Wl,-mllvm -Wl,-inline-recursion=4 \ -Wl,-mllvm -Wl,-lsr-in-nested-loop \ -Wl,-mllvm -Wl,-enable-iv-split # Libraries: EXTRA_LIBS = -lamdlibm \ -lm \ -lflang EXTRA_CLIBS = -lamdalloc-ext \ -ldl EXTRA_CXXLIBS = -lamdalloc-ext \ -ldl EXTRA_FLIBS = -lamdalloc \ -ldl ##################### # Peak tuning flags # ##################### default=peak: COPTIMIZE = $(OPT_ROOT_PEAK) \ -fstruct-layout=7 \ -mllvm -unroll-threshold=50 -fremap-arrays \ -fstrip-mining \ -mllvm -inline-threshold=1000 \ -mllvm -reduce-array-computations=3 \ -zopt CXXOPTIMIZE = $(OPT_ROOT_PEAK) \ -mllvm -unroll-threshold=100 \ -mllvm -reduce-array-computations=3 \ -zopt FOPTIMIZE = $(OPT_ROOT_PEAK) \ -Mrecursive \ -mllvm -reduce-array-computations=3 \ -fepilog-vectorization-of-inductions \ -zopt LDFLAGS = -Wl,-mllvm -Wl,-align-all-nofallthru-blocks=6 \ -Wl,-mllvm -Wl,-reduce-array-computations=3 LDCXXFLAGS = -Wl,-mllvm -Wl,-x86-use-vzeroupper=false feedback = 0 PASS1_CFLAGS = -fprofile-instr-generate PASS2_CFLAGS = -fprofile-instr-use PASS1_FFLAGS = -fprofile-generate PASS2_FFLAGS = -fprofile-use PASS1_CXXFLAGS = -fprofile-instr-generate PASS2_CXXFLAGS = -fprofile-instr-use PASS1_LDFLAGS = -fprofile-instr-generate PASS2_LDFLAGS = -fprofile-instr-use fdo_run1 = $command ; llvm-profdata merge --output=default.profdata *.profraw #libraries: EXTRA_LIBS = -lamdlibm \ -lm \ -lamdalloc \ -ldl EXTRA_FLIBS = -lflang ######################################## # Benchmark specific peak tuning flags # ######################################## 500.perlbench_r=peak: #lang='C' COPTIMIZE = $(OPT_ROOT_PEAK) \ -fstruct-layout=7 \ -mllvm -unroll-threshold=50 \ -fremap-arrays \ -mllvm -inline-threshold=1000 \ -mllvm -reduce-array-computations=3 \ -faggressive-loop-transform \ -fvector-transform \ -fscalar-transform feedback = 1 502.gcc_r=peak: #lang='C' EXTRA_PORTABILITY = -D_FILE_OFFSET_BITS=64 CC = clang -m32 CLD = clang -m32 -L/usr/lib32 EXTRA_LIBS = EXTRA_CLIBS = -L$[AMDALLOC_LIB32_PATH] -lamdalloc MATHLIBOPT = -lm LDFLAGS = -flto 505.mcf_r=peak: #lang='C' LDCFLAGS = -Wl,-mllvm -Wl,-extra-inliner 507.cactuBSSN_r=peak: CXXOPTIMIZE = $(OPT_ROOT_PEAK) \ -mllvm -unroll-threshold=100 \ -mllvm -loop-unswitch-threshold=200000 \ -mllvm -reduce-array-computations=3 \ -faggressive-loop-transform \ -fvector-transform \ -fscalar-transform EXTRA_LIBS += $(EXTRA_FLIBS) #adding flang libs to cxx linker 510.parest_r=peak: LDFLAGS = -flto \ -Wl,-mllvm -Wl,-suppress-fmas 511.povray_r=peak: #lang='CXX,C' COPTIMIZE = $(OPT_ROOT_PEAK) \ -fstruct-layout=7 \ -mllvm -unroll-threshold=50 \ -mllvm -inline-threshold=1000 \ -fremap-arrays \ -mllvm -reduce-array-computations=3 \ -zopt CXXOPTIMIZE = $(OPT_ROOT_PEAK) \ -mllvm -unroll-threshold=100 \ -mllvm -loop-unswitch-threshold=200000 \ -mllvm -reduce-array-computations=3 \ -zopt LDCXXFLAGS = -Wl,-mllvm -Wl,-x86-use-vzeroupper=false \ -Wl,-mllvm -Wl,-extra-inliner LDCFLAGS = -Wl,-mllvm -Wl,-ldist-scalar-expand \ -fenable-aggressive-gather EXTRA_LIBS = -lamdlibm -lm -lamdalloc -ldl 520.omnetpp_r=peak: #lang='CXX` EXTRA_LIBS = -lamdlibm -lm -lamdalloc-ext -ldl 523.xalancbmk_r=peak: #lang='CXX` EXTRA_CXXOPTIMIZE = -fvirtual-function-elimination \ -fvisibility=hidden \ -mllvm -do-block-reorder=advanced LDCXXFLAGS = -Wl,-mllvm -Wl,-do-block-reorder=advanced EXTRA_LIBS = -lamdlibm -lm -lflang EXTRA_CXXLIBS = -lamdalloc-ext -ldl ENV_MALLOC_CONF = thp:always 525.x264_r=peak: #lang='C' basepeak = yes 527.cam4_r=peak: COPTIMIZE = $(OPT_ROOT_PEAK) \ -fstruct-layout=7 \ -mllvm -unroll-threshold=50 \ -mllvm -inline-threshold=1000 \ -fremap-arrays \ -mllvm -reduce-array-computations=3 \ -zopt FOPTIMIZE = $(OPT_ROOT_PEAK) \ -Mrecursive \ -funroll-loops \ -mllvm -lsr-in-nested-loop \ -mllvm -reduce-array-computations=3 \ -fepilog-vectorization-of-inductions \ -zopt LDCFLAGS = -Wl,-mllvm -Wl,-ldist-scalar-expand \ -fenable-aggressive-gather LDFFLAGS = -Wl,-mllvm -Wl,-enable-X86-prefetching 531.deepsjeng_r=peak: #lang='CXX' CXXOPTIMIZE = $(OPT_ROOT_PEAK) \ -mllvm -unroll-threshold=100\ -mllvm -loop-unswitch-threshold=200000 \ -mllvm -reduce-array-computations=3 \ -zopt EXTRA_CXXOPTIMIZE = -fvirtual-function-elimination \ -fvisibility=hidden LDCXXFLAGS = EXTRA_LIBS = -lamdlibm -lm EXTRA_CXXLIBS = -lamdalloc-ext -ldl 544.nab_r=peak: LDFLAGS = -flto \ -Wl,-mllvm -Wl,-ldist-scalar-expand \ -fenable-aggressive-gather 549.fotonik3d_r=peak: FOPTIMIZE = $(OPT_ROOT_PEAK) \ -Mrecursive \ -mllvm -reduce-array-computations=3 \ -fepilog-vectorization-of-inductions \ -fvector-transform \ -fscalar-transform 521.wrf_r=peak: FOPTIMIZE = $(OPT_ROOT) \ -Ofast \ -Mrecursive \ -funroll-loops \ -mllvm -lsr-in-nested-loop \ -mllvm -reduce-array-computations=3 \ -Wno-unused-command-line-argument \ -fepilog-vectorization-of-inductions \ -zopt 554.roms_r=peak: FOPTIMIZE = $(OPT_ROOT_PEAK) \ -Mrecursive \ -mllvm -reduce-array-computations=3 \ -fepilog-vectorization-of-inductions \ -zopt # ---- End inclusion of '/home/cpu2k17/config/amd_rate_aocc500_znver5_A1_flags.inc' # The following settings were obtained by running the sysinfo_program # 'specperl $[top]/bin/sysinfo' (sysinfo:SHA:2eb381fc1a58eb8122e4a1b875c1e38b3489dac84088192aa0ec6d157b084d06) default: notes_plat_sysinfo_000 = notes_plat_sysinfo_005 = Sysinfo program /home/cpu2k17/bin/sysinfo notes_plat_sysinfo_010 = Rev: r6732 of 2022-11-07 fe91c89b7ed5c36ae2c92cc097bec197 notes_plat_sysinfo_015 = running on localhost Fri Sep 20 14:22:33 2024 notes_plat_sysinfo_020 = notes_plat_sysinfo_025 = SUT (System Under Test) info as seen by some common utilities. notes_plat_sysinfo_030 = notes_plat_sysinfo_035 = ------------------------------------------------------------ notes_plat_sysinfo_040 = Table of contents notes_plat_sysinfo_045 = ------------------------------------------------------------ notes_plat_sysinfo_050 = 1. uname -a notes_plat_sysinfo_055 = 2. w notes_plat_sysinfo_060 = 3. Username notes_plat_sysinfo_065 = 4. ulimit -a notes_plat_sysinfo_070 = 5. sysinfo process ancestry notes_plat_sysinfo_075 = 6. /proc/cpuinfo notes_plat_sysinfo_080 = 7. lscpu notes_plat_sysinfo_085 = 8. numactl --hardware notes_plat_sysinfo_090 = 9. /proc/meminfo notes_plat_sysinfo_095 = 10. who -r notes_plat_sysinfo_100 = 11. Systemd service manager version: systemd 254 (254.10+suse.84.ge8d77af424) notes_plat_sysinfo_105 = 12. Services, from systemctl list-unit-files notes_plat_sysinfo_110 = 13. Linux kernel boot-time arguments, from /proc/cmdline notes_plat_sysinfo_115 = 14. cpupower frequency-info notes_plat_sysinfo_120 = 15. sysctl notes_plat_sysinfo_125 = 16. /sys/kernel/mm/transparent_hugepage notes_plat_sysinfo_130 = 17. /sys/kernel/mm/transparent_hugepage/khugepaged notes_plat_sysinfo_135 = 18. OS release notes_plat_sysinfo_140 = 19. Disk information notes_plat_sysinfo_145 = 20. /sys/devices/virtual/dmi/id notes_plat_sysinfo_150 = 21. dmidecode notes_plat_sysinfo_155 = 22. BIOS notes_plat_sysinfo_160 = ------------------------------------------------------------ notes_plat_sysinfo_165 = notes_plat_sysinfo_170 = ------------------------------------------------------------ notes_plat_sysinfo_175 = 1. uname -a notes_plat_sysinfo_180 = Linux localhost 6.4.0-150600.21-default #1 SMP PREEMPT_DYNAMIC Thu May 16 11:09:22 UTC 2024 (36c1e09) notes_plat_sysinfo_185 = x86_64 x86_64 x86_64 GNU/Linux notes_plat_sysinfo_190 = notes_plat_sysinfo_195 = ------------------------------------------------------------ notes_plat_sysinfo_200 = 2. w notes_plat_sysinfo_205 = 14:22:33 up 33 min, 2 users, load average: 0.00, 0.00, 0.00 notes_plat_sysinfo_210 = USER TTY FROM LOGIN@ IDLE JCPU PCPU WHAT notes_plat_sysinfo_215 = root pts/0 172.17.1.13 14:20 9.00s 1.31s 0.07s /bin/bash ./amd_rate_aocc500_znver5_A1.sh notes_plat_sysinfo_220 = notes_plat_sysinfo_225 = ------------------------------------------------------------ notes_plat_sysinfo_230 = 3. Username notes_plat_sysinfo_235 = From environment variable $USER: root notes_plat_sysinfo_240 = notes_plat_sysinfo_245 = ------------------------------------------------------------ notes_plat_sysinfo_250 = 4. ulimit -a notes_plat_sysinfo_255 = core file size (blocks, -c) unlimited notes_plat_sysinfo_260 = data seg size (kbytes, -d) unlimited notes_plat_sysinfo_265 = scheduling priority (-e) 0 notes_plat_sysinfo_270 = file size (blocks, -f) unlimited notes_plat_sysinfo_275 = pending signals (-i) 3094624 notes_plat_sysinfo_280 = max locked memory (kbytes, -l) 2097152 notes_plat_sysinfo_285 = max memory size (kbytes, -m) unlimited notes_plat_sysinfo_290 = open files (-n) 1024 notes_plat_sysinfo_295 = pipe size (512 bytes, -p) 8 notes_plat_sysinfo_300 = POSIX message queues (bytes, -q) 819200 notes_plat_sysinfo_305 = real-time priority (-r) 0 notes_plat_sysinfo_310 = stack size (kbytes, -s) unlimited notes_plat_sysinfo_315 = cpu time (seconds, -t) unlimited notes_plat_sysinfo_320 = max user processes (-u) 3094624 notes_plat_sysinfo_325 = virtual memory (kbytes, -v) unlimited notes_plat_sysinfo_330 = file locks (-x) unlimited notes_plat_sysinfo_335 = notes_plat_sysinfo_340 = ------------------------------------------------------------ notes_plat_sysinfo_345 = 5. sysinfo process ancestry notes_plat_sysinfo_350 = /usr/lib/systemd/systemd --switched-root --system --deserialize=31 notes_plat_sysinfo_355 = sshd: /usr/sbin/sshd -D [listener] 0 of 10-100 startups notes_plat_sysinfo_360 = sshd: root [priv] notes_plat_sysinfo_365 = sshd: root@pts/0 notes_plat_sysinfo_370 = -bash notes_plat_sysinfo_375 = python3 ./run_fprate.py notes_plat_sysinfo_380 = /bin/bash ./amd_rate_aocc500_znver5_A1.sh notes_plat_sysinfo_385 = runcpu --config amd_rate_aocc500_znver5_A1.cfg --tune all --reportable --iterations 3 fprate notes_plat_sysinfo_390 = runcpu --configfile amd_rate_aocc500_znver5_A1.cfg --tune all --reportable --iterations 3 --nopower notes_plat_sysinfo_395 = --runmode rate --tune base:peak --size test:train:refrate fprate --nopreenv --note-preenv --logfile notes_plat_sysinfo_400 = $SPEC/tmp/CPU2017.005/templogs/preenv.fprate.005.0.log --lognum 005.0 --from_runcpu 2 notes_plat_sysinfo_405 = specperl $SPEC/bin/sysinfo notes_plat_sysinfo_410 = $SPEC = /home/cpu2k17 notes_plat_sysinfo_415 = notes_plat_sysinfo_420 = ------------------------------------------------------------ notes_plat_sysinfo_425 = 6. /proc/cpuinfo notes_plat_sysinfo_430 = model name : AMD EPYC 8534P 64-Core Processor notes_plat_sysinfo_435 = vendor_id : AuthenticAMD notes_plat_sysinfo_440 = cpu family : 25 notes_plat_sysinfo_445 = model : 160 notes_plat_sysinfo_450 = stepping : 2 notes_plat_sysinfo_455 = microcode : 0xaa00215 notes_plat_sysinfo_460 = bugs : sysret_ss_attrs spectre_v1 spectre_v2 spec_store_bypass srso notes_plat_sysinfo_465 = TLB size : 3584 4K pages notes_plat_sysinfo_470 = cpu cores : 64 notes_plat_sysinfo_475 = siblings : 128 notes_plat_sysinfo_480 = 1 physical ids (chips) notes_plat_sysinfo_485 = 128 processors (hardware threads) notes_plat_sysinfo_490 = physical id 0: core ids 0-63 notes_plat_sysinfo_495 = physical id 0: apicids 0-127 notes_plat_sysinfo_500 = Caution: /proc/cpuinfo data regarding chips, cores, and threads is not necessarily reliable, especially for notes_plat_sysinfo_505 = virtualized systems. Use the above data carefully. notes_plat_sysinfo_510 = notes_plat_sysinfo_515 = ------------------------------------------------------------ notes_plat_sysinfo_520 = 7. lscpu notes_plat_sysinfo_525 = notes_plat_sysinfo_530 = From lscpu from util-linux 2.39.3: notes_plat_sysinfo_535 = Architecture: x86_64 notes_plat_sysinfo_540 = CPU op-mode(s): 32-bit, 64-bit notes_plat_sysinfo_545 = Address sizes: 52 bits physical, 57 bits virtual notes_plat_sysinfo_550 = Byte Order: Little Endian notes_plat_sysinfo_555 = CPU(s): 128 notes_plat_sysinfo_560 = On-line CPU(s) list: 0-127 notes_plat_sysinfo_565 = Vendor ID: AuthenticAMD notes_plat_sysinfo_570 = BIOS Vendor ID: Advanced Micro Devices, Inc. notes_plat_sysinfo_575 = Model name: AMD EPYC 8534P 64-Core Processor notes_plat_sysinfo_580 = BIOS Model name: AMD EPYC 8534P 64-Core Processor CPU @ 2.3GHz notes_plat_sysinfo_585 = BIOS CPU family: 107 notes_plat_sysinfo_590 = CPU family: 25 notes_plat_sysinfo_595 = Model: 160 notes_plat_sysinfo_600 = Thread(s) per core: 2 notes_plat_sysinfo_605 = Core(s) per socket: 64 notes_plat_sysinfo_610 = Socket(s): 1 notes_plat_sysinfo_615 = Stepping: 2 notes_plat_sysinfo_620 = BogoMIPS: 4593.18 notes_plat_sysinfo_625 = Flags: fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat notes_plat_sysinfo_630 = pse36 clflush mmx fxsr sse sse2 ht syscall nx mmxext fxsr_opt pdpe1gb notes_plat_sysinfo_635 = rdtscp lm constant_tsc rep_good amd_lbr_v2 nopl nonstop_tsc cpuid notes_plat_sysinfo_640 = extd_apicid aperfmperf rapl pni pclmulqdq monitor ssse3 fma cx16 pcid notes_plat_sysinfo_645 = sse4_1 sse4_2 movbe popcnt aes xsave avx f16c rdrand lahf_lm notes_plat_sysinfo_650 = cmp_legacy svm extapic cr8_legacy abm sse4a misalignsse 3dnowprefetch notes_plat_sysinfo_655 = osvw ibs skinit wdt tce topoext perfctr_core perfctr_nb bpext notes_plat_sysinfo_660 = perfctr_llc mwaitx cpb cat_l3 cdp_l3 hw_pstate ssbd mba perfmon_v2 notes_plat_sysinfo_665 = ibrs ibpb stibp ibrs_enhanced vmmcall fsgsbase bmi1 avx2 smep bmi2 notes_plat_sysinfo_670 = erms invpcid cqm rdt_a avx512f avx512dq rdseed adx smap avx512ifma notes_plat_sysinfo_675 = clflushopt clwb avx512cd sha_ni avx512bw avx512vl xsaveopt xsavec notes_plat_sysinfo_680 = xgetbv1 xsaves cqm_llc cqm_occup_llc cqm_mbm_total cqm_mbm_local notes_plat_sysinfo_685 = user_shstk avx512_bf16 clzero irperf xsaveerptr rdpru wbnoinvd notes_plat_sysinfo_690 = amd_ppin cppc arat npt lbrv svm_lock nrip_save tsc_scale vmcb_clean notes_plat_sysinfo_695 = flushbyasid decodeassists pausefilter pfthreshold avic notes_plat_sysinfo_700 = v_vmsave_vmload vgif x2avic v_spec_ctrl vnmi avx512vbmi umip pku notes_plat_sysinfo_705 = ospke avx512_vbmi2 gfni vaes vpclmulqdq avx512_vnni avx512_bitalg notes_plat_sysinfo_710 = avx512_vpopcntdq la57 rdpid overflow_recov succor smca fsrm flush_l1d notes_plat_sysinfo_715 = debug_swap notes_plat_sysinfo_720 = Virtualization: AMD-V notes_plat_sysinfo_725 = L1d cache: 2 MiB (64 instances) notes_plat_sysinfo_730 = L1i cache: 2 MiB (64 instances) notes_plat_sysinfo_735 = L2 cache: 64 MiB (64 instances) notes_plat_sysinfo_740 = L3 cache: 128 MiB (8 instances) notes_plat_sysinfo_745 = NUMA node(s): 2 notes_plat_sysinfo_750 = NUMA node0 CPU(s): 0-31,64-95 notes_plat_sysinfo_755 = NUMA node1 CPU(s): 32-63,96-127 notes_plat_sysinfo_760 = Vulnerability Gather data sampling: Not affected notes_plat_sysinfo_765 = Vulnerability Itlb multihit: Not affected notes_plat_sysinfo_770 = Vulnerability L1tf: Not affected notes_plat_sysinfo_775 = Vulnerability Mds: Not affected notes_plat_sysinfo_780 = Vulnerability Meltdown: Not affected notes_plat_sysinfo_785 = Vulnerability Mmio stale data: Not affected notes_plat_sysinfo_790 = Vulnerability Reg file data sampling: Not affected notes_plat_sysinfo_795 = Vulnerability Retbleed: Not affected notes_plat_sysinfo_800 = Vulnerability Spec rstack overflow: Mitigation; Safe RET notes_plat_sysinfo_805 = Vulnerability Spec store bypass: Mitigation; Speculative Store Bypass disabled via prctl notes_plat_sysinfo_810 = Vulnerability Spectre v1: Mitigation; usercopy/swapgs barriers and __user pointer sanitization notes_plat_sysinfo_815 = Vulnerability Spectre v2: Mitigation; Enhanced / Automatic IBRS; IBPB conditional; STIBP notes_plat_sysinfo_820 = always-on; RSB filling; PBRSB-eIBRS Not affected; BHI Not affected notes_plat_sysinfo_825 = Vulnerability Srbds: Not affected notes_plat_sysinfo_830 = Vulnerability Tsx async abort: Not affected notes_plat_sysinfo_835 = notes_plat_sysinfo_840 = From lscpu --cache: notes_plat_sysinfo_845 = NAME ONE-SIZE ALL-SIZE WAYS TYPE LEVEL SETS PHY-LINE COHERENCY-SIZE notes_plat_sysinfo_850 = L1d 32K 2M 8 Data 1 64 1 64 notes_plat_sysinfo_855 = L1i 32K 2M 8 Instruction 1 64 1 64 notes_plat_sysinfo_860 = L2 1M 64M 8 Unified 2 2048 1 64 notes_plat_sysinfo_865 = L3 16M 128M 16 Unified 3 16384 1 64 notes_plat_sysinfo_870 = notes_plat_sysinfo_875 = ------------------------------------------------------------ notes_plat_sysinfo_880 = 8. numactl --hardware notes_plat_sysinfo_885 = NOTE: a numactl 'node' might or might not correspond to a physical chip. notes_plat_sysinfo_890 = available: 2 nodes (0-1) notes_plat_sysinfo_895 = node 0 cpus: 0-31,64-95 notes_plat_sysinfo_900 = node 0 size: 386705 MB notes_plat_sysinfo_905 = node 0 free: 385808 MB notes_plat_sysinfo_910 = node 1 cpus: 32-63,96-127 notes_plat_sysinfo_915 = node 1 size: 386976 MB notes_plat_sysinfo_920 = node 1 free: 385868 MB notes_plat_sysinfo_925 = node distances: notes_plat_sysinfo_930 = node 0 1 notes_plat_sysinfo_935 = 0: 10 12 notes_plat_sysinfo_940 = 1: 12 10 notes_plat_sysinfo_945 = notes_plat_sysinfo_950 = ------------------------------------------------------------ notes_plat_sysinfo_955 = 9. /proc/meminfo notes_plat_sysinfo_960 = MemTotal: 792249652 kB notes_plat_sysinfo_965 = notes_plat_sysinfo_970 = ------------------------------------------------------------ notes_plat_sysinfo_975 = 10. who -r notes_plat_sysinfo_980 = run-level 3 Sep 20 13:51 notes_plat_sysinfo_985 = notes_plat_sysinfo_990 = ------------------------------------------------------------ notes_plat_sysinfo_995 = 11. Systemd service manager version: systemd 254 (254.10+suse.84.ge8d77af424) notes_plat_sysinfo_1000= Default Target Status notes_plat_sysinfo_1005= multi-user running notes_plat_sysinfo_1010= notes_plat_sysinfo_1015= ------------------------------------------------------------ notes_plat_sysinfo_1020= 12. Services, from systemctl list-unit-files notes_plat_sysinfo_1025= STATE UNIT FILES notes_plat_sysinfo_1030= enabled apparmor auditd cron getty@ irqbalance issue-generator kbdsettings postfix purge-kernels notes_plat_sysinfo_1035= rollback sshd systemd-pstore wicked wickedd-auto4 wickedd-dhcp4 wickedd-dhcp6 notes_plat_sysinfo_1040= wickedd-nanny notes_plat_sysinfo_1045= enabled-runtime systemd-remount-fs notes_plat_sysinfo_1050= disabled boot-sysctl ca-certificates chrony-wait chronyd console-getty debug-shell grub2-once notes_plat_sysinfo_1055= haveged hwloc-dump-hwdata issue-add-ssh-keys kexec-load lunmask rpmconfigcheck notes_plat_sysinfo_1060= serial-getty@ systemd-boot-check-no-failures systemd-confext systemd-network-generator notes_plat_sysinfo_1065= systemd-sysext systemd-time-wait-sync systemd-timesyncd notes_plat_sysinfo_1070= indirect systemd-userdbd wickedd notes_plat_sysinfo_1075= notes_plat_sysinfo_1080= ------------------------------------------------------------ notes_plat_sysinfo_1085= 13. Linux kernel boot-time arguments, from /proc/cmdline notes_plat_sysinfo_1090= BOOT_IMAGE=/boot/vmlinuz-6.4.0-150600.21-default notes_plat_sysinfo_1095= root=UUID=fe97c644-1a1b-45c1-9618-5870ddb81128 notes_plat_sysinfo_1100= splash=silent notes_plat_sysinfo_1105= mitigations=auto notes_plat_sysinfo_1110= quiet notes_plat_sysinfo_1115= security=apparmor notes_plat_sysinfo_1120= notes_plat_sysinfo_1125= ------------------------------------------------------------ notes_plat_sysinfo_1130= 14. cpupower frequency-info notes_plat_sysinfo_1135= analyzing CPU 55: notes_plat_sysinfo_1140= Unable to determine current policy notes_plat_sysinfo_1145= boost state support: notes_plat_sysinfo_1150= Supported: yes notes_plat_sysinfo_1155= Active: yes notes_plat_sysinfo_1160= notes_plat_sysinfo_1165= ------------------------------------------------------------ notes_plat_sysinfo_1170= 15. sysctl notes_plat_sysinfo_1175= kernel.numa_balancing 1 notes_plat_sysinfo_1180= kernel.randomize_va_space 0 notes_plat_sysinfo_1185= vm.compaction_proactiveness 20 notes_plat_sysinfo_1190= vm.dirty_background_bytes 0 notes_plat_sysinfo_1195= vm.dirty_background_ratio 10 notes_plat_sysinfo_1200= vm.dirty_bytes 0 notes_plat_sysinfo_1205= vm.dirty_expire_centisecs 3000 notes_plat_sysinfo_1210= vm.dirty_ratio 8 notes_plat_sysinfo_1215= vm.dirty_writeback_centisecs 500 notes_plat_sysinfo_1220= vm.dirtytime_expire_seconds 43200 notes_plat_sysinfo_1225= vm.extfrag_threshold 500 notes_plat_sysinfo_1230= vm.min_unmapped_ratio 1 notes_plat_sysinfo_1235= vm.nr_hugepages 0 notes_plat_sysinfo_1240= vm.nr_hugepages_mempolicy 0 notes_plat_sysinfo_1245= vm.nr_overcommit_hugepages 0 notes_plat_sysinfo_1250= vm.swappiness 1 notes_plat_sysinfo_1255= vm.watermark_boost_factor 15000 notes_plat_sysinfo_1260= vm.watermark_scale_factor 10 notes_plat_sysinfo_1265= vm.zone_reclaim_mode 1 notes_plat_sysinfo_1270= notes_plat_sysinfo_1275= ------------------------------------------------------------ notes_plat_sysinfo_1280= 16. /sys/kernel/mm/transparent_hugepage notes_plat_sysinfo_1285= defrag [always] defer defer+madvise madvise never notes_plat_sysinfo_1290= enabled [always] madvise never notes_plat_sysinfo_1295= hpage_pmd_size 2097152 notes_plat_sysinfo_1300= shmem_enabled always within_size advise [never] deny force notes_plat_sysinfo_1305= notes_plat_sysinfo_1310= ------------------------------------------------------------ notes_plat_sysinfo_1315= 17. /sys/kernel/mm/transparent_hugepage/khugepaged notes_plat_sysinfo_1320= alloc_sleep_millisecs 60000 notes_plat_sysinfo_1325= defrag 1 notes_plat_sysinfo_1330= max_ptes_none 511 notes_plat_sysinfo_1335= max_ptes_shared 256 notes_plat_sysinfo_1340= max_ptes_swap 64 notes_plat_sysinfo_1345= pages_to_scan 4096 notes_plat_sysinfo_1350= scan_sleep_millisecs 10000 notes_plat_sysinfo_1355= notes_plat_sysinfo_1360= ------------------------------------------------------------ notes_plat_sysinfo_1365= 18. OS release notes_plat_sysinfo_1370= From /etc/*-release /etc/*-version notes_plat_sysinfo_1375= os-release SUSE Linux Enterprise Server 15 SP6 notes_plat_sysinfo_1380= notes_plat_sysinfo_1385= ------------------------------------------------------------ notes_plat_sysinfo_1390= 19. Disk information notes_plat_sysinfo_1395= SPEC is set to: /home/cpu2k17 notes_plat_sysinfo_1400= Filesystem Type Size Used Avail Use% Mounted on notes_plat_sysinfo_1405= /dev/sda3 btrfs 446G 66G 377G 15% /home notes_plat_sysinfo_1410= notes_plat_sysinfo_1415= ------------------------------------------------------------ notes_plat_sysinfo_1420= 20. /sys/devices/virtual/dmi/id notes_plat_sysinfo_1425= Vendor: HPE notes_plat_sysinfo_1430= Product: ProLiant DL145 Gen11 notes_plat_sysinfo_1435= Product Family: ProLiant notes_plat_sysinfo_1440= Serial: 41600016J0A1 notes_plat_sysinfo_1445= notes_plat_sysinfo_1450= ------------------------------------------------------------ notes_plat_sysinfo_1455= 21. dmidecode notes_plat_sysinfo_1460= Additional information from dmidecode 3.4 follows. WARNING: Use caution when you interpret this section. notes_plat_sysinfo_1465= The 'dmidecode' program reads system data which is "intended to allow hardware to be accurately notes_plat_sysinfo_1470= determined", but the intent may not be met, as there are frequent changes to hardware, firmware, and the notes_plat_sysinfo_1475= "DMTF SMBIOS" standard. notes_plat_sysinfo_1480= Memory: notes_plat_sysinfo_1485= 1x Hynix HMCT04MEERA129N 128 GB 4 rank 4800 notes_plat_sysinfo_1490= 5x Hynix HMCT04MEERA133N 128 GB 4 rank 4800 notes_plat_sysinfo_1495= notes_plat_sysinfo_1500= notes_plat_sysinfo_1505= ------------------------------------------------------------ notes_plat_sysinfo_1510= 22. BIOS notes_plat_sysinfo_1515= (This section combines info from /sys/devices and dmidecode.) notes_plat_sysinfo_1520= BIOS Vendor: HPE notes_plat_sysinfo_1525= BIOS Version: 1.20 notes_plat_sysinfo_1530= BIOS Date: 08/09/2024 notes_plat_sysinfo_1535= BIOS Revision: 1.20 notes_plat_sysinfo_1540= Firmware Revision: 1.62 hw_cpu_name = AMD EPYC 8534P hw_disk = 446 GB add more disk info here hw_memory001 = 755.548 GB fixme: If using DDR4, the format is: hw_memory002 = 'N GB (N x N GB nRxn PC4-nnnnX-X)' hw_nchips = 1 hw_ncores = 64 hw_nthreadspercore = 2 prepared_by = root (is never output, only tags rawfile) sw_file = btrfs sw_os001 = SUSE Linux Enterprise Server 15 SP6 sw_state = Run level 3 (add definition here) # End of settings added by sysinfo_program 507.cactuBSSN_r: # The following setting was inserted automatically as a result of # post-run basepeak application. basepeak = 1 503.bwaves_r: # The following setting was inserted automatically as a result of # post-run basepeak application. basepeak = 1 # The following section was added automatically, and contains settings that # did not appear in the original configuration file, but were added to the # raw file after the run. default: power_management000 = BIOS set to prefer performance at power_management001 = the cost of additional power usage notes_plat_000 = BIOS Configuration notes_plat_005 = Workload Profile set to General Throughput Compute notes_plat_010 = Determinism Control set to Manual notes_plat_015 = Performance Determinism set to Power Deterministic notes_plat_020 = AMD Periodic Directory Rinse Tuning set to Cache-Bound notes_plat_025 = Memory Patrol Scrubbing set to Disabled notes_plat_030 = NUMA memory domains per socket set to Two memory domains per socket notes_plat_035 = ACPI CST C2 Latency set to 18 microseconds notes_plat_040 = Thermal Configuration set to Maximum Cooling notes_plat_045 = Workload Profile set to Custom notes_plat_050 = L2 HW Prefetcher set to Disabled notes_plat_055 = The reference code/AGESA version used in this ROM is version Siena-PI 1.0.0