SPEC CPU2017 Platform Settings for ASUSTek Systems

Operating System Tuning Parameters

cpupower:

The OS 'cpupower' utility is used to change CPU power governors settings. Available settings are:

• Performance: Run the CPU at the maximum frequency.
• powersave(default): Run the CPU at the minimum frequency.
• ondemand: Scales the frequency dynamically according to current load. Jumps to the highest frequency and then possibly back off as the idle time increases.

kernel.randomize_va_space (ASLR)

This setting can be used to select the type of process address space randomization. Defaults differ based on whether the architecture supports ASLR, whether the kernel was built with the CONFIG_COMPAT_BRK option or not, or the kernel boot options used.
Possible settings:

• 0: Turn process address space randomization off.
• 1: Randomize addresses of mmap base, stack, and VDSO pages.
• 2: Additionally randomize the heap. (This is probably the default.)

Disabling ASLR can make process execution more deterministic and runtimes more consistent. For more information see the randomize_va_space entry in the Linux sysctl documentation.

Transparent Hugepages (THP)

THP is an abstraction layer that automates most aspects of creating, managing, and using huge pages. It is designed to hide much of the complexity in using huge pages from system administrators and developers. Huge pages increase the memory page size from 4 kilobytes to 2 megabytes. This provides significant performance advantages on systems with highly contended resources and large memory workloads. If memory utilization is too high or memory is badly fragmented which prevents hugepages being allocated, the kernel will assign smaller 4k pages instead. Most recent Linux OS releases have THP enabled by default.
THP usage is controlled by the sysfs setting /sys/kernel/mm/transparent_hugepage/enabled. Possible values:

• never: entirely disable THP usage.
• madvise: enable THP usage only inside regions marked MADV_HUGEPAGE using madvise(3).
• always: enable THP usage system-wide. This is the default.

THP creation is controlled by the sysfs setting /sys/kernel/mm/transparent_hugepage/defrag. Possible values:

• never: if no THP are available to satisfy a request, do not attempt to make any.
• defer: an allocation requesting THP when none are available get normal pages while requesting THP creation in the background.
• defer+madvise: acts like "always", but only for allocations in regions marked MADV_HUGEPAGE using madvise(3); for all other regions it's like "defer".
• madvise: acts like "always", but only for allocations in regions marked MADV_HUGEPAGE using madvise(3). This is the default.
• always: an allocation requesting THP when none are available will stall until some are made.

An application that "always" requests THP often can benefit from waiting for an allocation until those huge pages can be assembled.
For more information see the Linux transparent hugepage documentation.

Firmware / BIOS / Microcode Settings

Determinism Slider:

This BIOS option allows for AGESA determinism to control performance.

• Performance: Provides predictable performance across all processors of the same type.
• Power: Maximizes performance within the power limits defined by cTDP and PPT.
• Auto (Default setting): Use AGESA default value for deterministic performance control.

cTDP Control:

This BIOS option is for "Configurable TDP (cTDP)", it allows user can set customized value for TDP. Available settings are:

• Auto: Use the fused TDP value.
• Manual(Default setting): Let user specifies customized TDP value.

cTDP:

TDP is an acronym for "Thermal Design Power." TDP is the recommended target for power used when designing the cooling capacity for a server. EPYC processors are able to control this target power consumption within certain limits. This capability is referred to as "configurable TDP" or "cTDP." cTDP can be used to reduce power consumption for greater efficiency, or in some cases, increase power consumption above the default value to provide additional performance. cTDP is controlled using a BIOS option.

The default EPYC cTDP value corresponds with the microprocessor's nominal TDP. The default cTDP value is set at a good balance between performance and energy efficiency. The EPYC 7763 cTDP can be reduced as low as 225W, which will minimize the power consumption for the processor under load, but at the expense of peak performance. Increasing the EPYC 7763 cTDP to 280W will maximize peak performance by allowing the CPU to maintain higher dynamic clock speeds, but will make the microprocessor less energy efficient. Note that at maximum cTDP, the CPU thermal solution must be capable of dissipating at least 280W or the EPYC 7763 processor might engage in thermal throttling under load.

The available cTDP ranges for each EPYC model are in the table below:

Model	Minimum cTDP	Maximum cTDP
EPYC 7773X	225	280
EPYC 7573X	225	280
EPYC 7473X	225	280
EPYC 7373X	225	280
EPYC 7763	225	280
EPYC 7713	225	240
EPYC 7713P	225	240
EPYC 7663	225	240
EPYC 7643	225	240
EPYC 75F3	225	280
EPYC 7543	225	240
EPYC 7543P	225	240
EPYC 7513	165	200
EPYC 7453	225	240
EPYC 74F3	225	240
EPYC 7443	165	200
EPYC 7443P	165	200
EPYC 7413	165	200
EPYC 73F3	225	240
EPYC 7343	165	200
EPYC 7313	155	180
EPYC 7313P	155	180
EPYC 72F3	165	200

* cTDP must remain below the thermal solution design parameters or thermal throttling could be frequently encountered.

Power phase shedding:

Power phase shedding allows efficiency optimization of the voltage regulator across the variety of loads, minimizing average energy consumption by optimizing the powertrain for specific load power states. Values for this BIOS option can be: Enabled/Disabled. Current default is Enabled.

SVM Mode:

This is CPU virtualization function. With SVM enabled you'll be able to install a virtual machine on your system. Values for this BIOS option can be: Enabled/Disabled. Current default is Enabled.

SR-IOV support:

In virtualization, single root input/output virtualization or SR-IOV is a specification that allows the isolation of the PCI Express resources for manageability and performance reasons. A single physical PCI Express can be shared on a virtual environment using the SR-IOV specification. If system has SR-IOV capable PCIe Devices, this option Enables or Disables Single Root IO Virtualization Support. Values for this BIOS option can be: Enabled/Disabled. Current default is Disabled.

DRAM Scrub time:

DRAM scrubbing is a mechanism for the memory controller to periodically read all memory locations and write back corrected data. The time interval for scrubbing the entire memory can be: Disabled/1 hour/4 hours/8 hours/16 hours/24 hours/48 hours/Auto. Current default is Auto(AGESA default value).

NUMA nodes per socket:

Specifies the number of desired NUMA nodes per populated socket in the system:

• NPS1: Each physical processor is a NUMA node, and memory accesses are interleaved across all memory channels directly connected to the physical processor.
• NPS2: Each physical processor is two NUMA nodes, and memory accesses are interleaved across 4 memory channels.
• NPS4: Each physical processor is four NUMA nodes, and memory accesses are interleaved across 2 memory channels.
• Auto: Use AGESA default value. Current default is NPS1

Current default is Auto.

APBDIS:

Application Power Management (APM) allows the processor to provide maximum performance while remaining within the specified power delivery and removal envelope. APM dynamically monitors processor activity and generates an approximation of power consumption. If power consumption exceeds a defined power limit, a P-state limit is applied by APM hardware to reduce power consumption. APM ensures that average power consumption over a thermally significant time period remains at or below the defined power limit. Set APBDIS=1 will disable Data Fabric APM and the SOC P-state will be fixed. Available settings are:

• 0: Disable APBDIS.
• 1: Enable APBDIS.
• Auto (Default setting): Use default value for APBDIS. The current value is 0.

Fix SOC P-state:

To minimize variance or trade-off memory latency versus bandwidth, algorithm performance boost (APBDIS) can be set and specific hard-fused Data Fabric (SoC) P-states forced for optimized workloads sensitive to latency or throughput. Available settings are:

• P0: The highest SOC P-state.
• P1
• P2
• P3: The lowest SOC P-state.
• Auto (Default setting): Use AGESA default value.

ACPI SRAT L3 Cache as NUMA Domain:

Each L3 Cache will be exposed as a NUMA node when enabling ACPI SRAT L3 Cache as a NUMA node. On a dual processor system, with up to 8 L3 Caches per processor, this setting will expose 16 NUMA domains. Available settings are:

• Auto (Default setting): Disable this function.
• Enabled: Enable this function.

Package Power Limit Control:

This BIOS option allows user can set customized value for processor package power limit(PPT). Available settings are:

• Auto: Use the fused PPT.
• Manual(Default setting): User can set customized PPT.

DLWM Support:

Dynamic Link Width Management(DLWM) reduces xGMI lane width from x16 to x8 or x2 if xGMI links have limited traffic. DLWM feature is optimized to trade power between CPU core intensive workloads and I/O bandwidth intensiveworkloads. When link activity is above a threshold, DLWM will increase lane width from x8 to x16 at the cost of some delay, because the I/O die must disconnect the links, retrain them at the new speed and release the system back to functionality. Values for this BIOS option can be: Auto/Enabled/Disabled. Current default is Auto.(Use AGESA default value. Current is Enabled.)

Engine Boost:

ASUS individual feature with the power acceleration design to increase CPU over-all performance. Available settings are: disabled(default) and enabled. Enable it could improve performance, but comes with more power consumption.

Package Power Limit:

Set customize processor Package Power Limit (PPT) value to be used on all populated processors in the system. Current default value is 240 = Use the 240W PPT value. ***PPT will be used as the ASIC power limit***

IOMMU:

The Input-Output Memory Management Unit(IOMMU) provides several benefits and is required when using x2APIC. Enabling the IOMMU allows devices (such as the EPYC integrated SATA controller) to present separate IRQs for each attached device instead of one IRQ for the subsystem. The IOMMU also allows operating systems to provide additional protection for DMA capable I/O devices. Values for this BIOS option can be: Auto/Enabled/Disabled. Current default is Auto.(Use AGESA default value. Current is Enabled.)

Memory Interleaving:

Memory interleaving is a technique that CPUs use to increase the memory bandwidth available for an application. Without interleaving, consecutive memory blocks, often cache lines, are read from the same memory bank. Because of this, software that reads consecutive memory must wait for a memory transfer to complete before starting the next memory access, reducing throughput and increasing latency. By enabling memory interleaving, consecutive memory blocks are in different banks and can all contribute to the overall memory bandwidth, thus increasing throughput and lowering latency. Values for this BIOS option can be: Auto/Disabled. Current default is Auto.(Use AGESA default value. Current is Enabled.)