# Invocation command line: # /cpu2000_mfs/cpu2000_1.2/bin/runspec --config=CJB32-jul17 --reportable --rate --users=32 int ############################################################################ ##################################################################### # SUT/Experimenter Section # If it affects performance, you need to describe it, either # in the pre-defined fields or by adding it to the notes section. # System Description - edit as needed hw_avail = Aug-2002 hw_model = AlphaServer GS320 Model 16 68/1224 machine_name = AlphaServer GS320 Model 16 68/1224 hw_memory = 128GB hw_disk = mfs (Memory File System) hw_other = None hw_vendor = Hewlett-Packard Company company_name = Hewlett-Packard Company # CPU description - edit as needed # Note ncpu = number enabled; ncpuorder = valid numbers of CPUs # to order for this model hw_cpu = Alpha 21264C hw_cpu_mhz = 1224 hw_fpu = Integrated hw_ncpu = 32 hw_ncpuorder = 1 to 32 hw_parallel = No hw_pcache = 64KB(I)+64KB(D) on chip hw_scache = 16MB off chip per CPU hw_tcache = None hw_ocache = None # Tester description - edit the date, put your name here. Notice that # "tester_name" is the company, but as it says in the documentation, # "prepared_by" can be personal: # # prepared_by Is never output. If you wish, you could set this to # your own name, so that the rawfile will be tagged with # your name but not the formal reports. test_date = Jul-2002 license_num = 2 prepared_by = Chris Beer tester_name = HPQ - NH # Operating system, file system - edit at least the OS version sw_os = Tru64 UNIX V5.1B-6 (Rev. 2610) sw_file = mfs sw_state = Multi-user # Special notes # If you have notes to add, put them here, starting with number 900. # sw_os2 = +Patch Kit 2 notes900 = notes901 = # OS Date # Use the "sw_avail" line here only if the OS you are testing ships # later than the compilers (and then comment out their availability # dates, below!) Notice that the field "sw_avail" occurs multiple # times in this file, but only one should be used on a given run: # # - the OS date (if later than the compilers), or # - the last complier date (may be different for FP vs. Int) #sw_avail = Nov-2000 # With luck, you shouldn't have to edit below this point # (unless you are installing new compilers or re-tuning) # End of SUT/Experimenter section ###################################################################### #submit= echo "$command" > dobmk; prun -n 1 sh dobmk #command_add_redirect=1 submit = runon $SPECUSERNUM $command ###################################################################### # The special "un-named" section of the config file. Must appear # before any instances of "default=" ext = jul17 output_format = asc #reportable = 1 teeout = no teerunout = yes tune = all ###################################################################### # Compiler selection - See "OS Date" above! Remember, it's the # LAST compiler in a set whose date should be listed. Remember that # C is used on both suites. Remember KAP dates. Remember to include # KAP C if "kcc" is ever used (it's probably not the default, so won't # be listed here under "CC", but should be listed as a sw_compiler if it # is used anywhere else in the file). default=default=default=default: sw_compiler = Compaq C V6.4-215-46B7O sw_compiler2 = Program Analysis Tools V2.0 sw_compiler3 = Spike V5.2 DTK (1.471.2.2 46B5P) sw_avail = Oct-2001 CC = cc -v notes950 = notes951 = Spike, and the Program Analysis Tools, are part of the Developers' notes952 = Tool Kit Supplement, http://www.tru64unix.compaq.com/dtk/ . The notes953 = features used in this SPEC submission will be available at the web notes954 = site as a production release in October, 2001. The C compiler for notes955 = this SPEC submission has been available at the same location, as a notes956 = production release, since May, 2001. int=default=default=default: sw_compiler4 = Compaq C++ V6.3-010-46B2F CXX = cxx -v fp=default=default=default: sw_compiler4 = Compaq Fortran V5.4A-1472-46B2F sw_compiler5 = Compaq Fortran 77 V5.4A-196-46B2F sw_compiler6 = KAP Fortran V4.3 000607 sw_compiler7 = KAP Fortran 77 V4.1 980926 sw_compiler8 = KAP C V4.1 000607 FC = f90 -v # Notice that in the compiler selection above, we always ask for -v, # verbose mode. SPEC has said that it would prefer that notes sections # NOT document the use of "-v". OK, I've dropped it from the notes # sections, but it's here in the config file and plain to see for anyone # who really cares. The effect of -v is simply to cause the driver to use # verbose mode, but it has no effect on the generated executable. ######################################################################### # # Feedback description. When using feedback for individual benchmarks, # do it strictly as described here, so that this comment remains correct. # (Unfortunately, there is no convenient macro mechanism to enforce this # automatically, so just do it.) default=default=default=default: notes700 = notes701 = Most benchmarks are built using one or more types of notes702 = profile-driven feedback. The types used are designated notes703 = by abbreviations in the notes: notes704 = notes705 = +CFB: Code generation is optimized by the compiler, using notes706 = feedback from a training run. These commands are notes707 = done before the first compile (in phase "fdo_pre0"): notes708 = notes710 = mkdir /tmp/pp notes711 = rm -f /tmp/pp/${baseexe}* notes712 = notes713 = and these flags are added to the first and second compiles: notes714 = notes715 = PASS1_CFLAGS = -prof_gen_noopt -prof_dir /tmp/pp notes716 = PASS2_CFLAGS = -prof_use -prof_dir /tmp/pp notes717 = notes718 = (Peak builds use /tmp/pp above; base builds use /tmp/pb.) notes719 = notes720 = +IFB: Icache usage is improved by the post-link-time optimizer notes721 = Spike, using feedback from a training run. These commands notes722 = are used (in phase "fdo_postN"): notes723 = notes724 = mv ${baseexe} oldexe notes725 = spike oldexe -feedback oldexe -o ${baseexe} notes726 = notes727 = +PFB: Prefetches are improved by the post-link-time optimizer notes728 = Spike, using feedback from a training run. These notes729 = commands are used (in phase "fdo_post_makeN"): notes730 = notes731 = rm -f *Counts* notes732 = mv ${baseexe} oldexe notes733 = pixie -stats dstride oldexe 1>pixie.out 2>pixie.err notes734 = mv oldexe.pixie ${baseexe} notes735 = notes736 = A training run is carried out (in phase "fdo_runN"), and notes737 = then this command (in phase "fdo_postN"): notes738 = notes739 = spike oldexe -fb oldexe -stride_prefetch -o ${baseexe} notes740 = notes741 = When Spike is used for both Icache and Prefetch improvements, notes742 = only one spike command is actually issued, with the Icache notes743 = options followed by the Prefetch options. ####################################################################### # Integer Baseline Optimization # notes0xx are used for baseline tuning description int=base=default=default: notes000 = Baseline C : cc -arch ev6 -fast +CFB ONESTEP notes001 = C++: cxx -arch ev6 -O2 ONESTEP OPTIMIZE = -v -arch ev6 COPTIMIZE = -fast CXXOPTIMIZE = -O2 ONESTEP = yes fdo_pre0 = mkdir /tmp/pb; rm -f /tmp/pb/${baseexe}* PASS1_CFLAGS = -prof_gen_noopt -prof_dir /tmp/pb PASS2_CFLAGS = -prof_use_feedback -prof_dir /tmp/pb 252.eon=base=default=default: # Turn feedback off for eon fdo_pre0 = ####################################################################### # Integer Peak # notes10x are used for peak tuning description, followed by the # actual benchmark numbers (e.g. notes253 and (if needed) notes253_1 # for perlbmk) int=peak=default=default: notes100 = notes101 = Peak: notes102 = All but 252.eon: cc -g3 -arch ev6 ONESTEP OPTIMIZE = -v -g3 -arch ev6 ONESTEP = yes # GEM Feedback - turn off in individual benchmark if not needed. fdo_pre0 = mkdir /tmp/pp; rm -f /tmp/pp/${baseexe}* PASS1_CFLAGS = -prof_gen_noopt -prof_dir /tmp/pp PASS2_CFLAGS = -prof_use_feedback -prof_dir /tmp/pp 164.gzip=peak=default=default: notes164 = 164.gzip: -fast -O4 -non_shared +CFB COPTIMIZE = -fast -O4 -non_shared feedback = 1 175.vpr=peak=default=default: notes175 = 175.vpr: -fast -O4 -assume restricted_pointers +CFB COPTIMIZE = -fast -O4 -assume restricted_pointers feedback = 1 176.gcc=peak=default=default: notes176 = 176.gcc: -fast -O4 -xtaso_short -all -ldensemalloc -none notes176_1 = +CFB +IFB COPTIMIZE = -fast -O4 -xtaso_short -all -ldensemalloc -none feedback = 1 fdo_post2 = <pixie.out 2>pixie.err mv oldexe.pixie ${baseexe} EOT fdo_run2 = $command fdo_post2 = <pixie.out 2>pixie.err mv oldexe.pixie ${baseexe} EOT fdo_run2 = $command fdo_post2 = <pixie.out 2>pixie.err mv oldexe.pixie ${baseexe} EOT fdo_post1 = spike oldexe -fb oldexe -stride_prefetch -o ${baseexe} 171.swim=peak=default=default: notes171 = 171.swim: f90 -fast -O5 F77OPTIMIZE = -fast -O5 F77 = f90 172.mgrid=peak=default=default: notes172 = 172.mgrid: kf77 -O5 -transform_loops -tune ev6 -unroll 8 notes172_1 +PFB F77OPTIMIZE = -O5 -transform_loops -tune ev6 -unroll 8 F77 = kf77 fdo_post_make1 = <pixie.out 2>pixie.err mv oldexe.pixie ${baseexe} EOT fdo_post1 = spike oldexe -fb oldexe -stride_prefetch -o ${baseexe} 173.applu=peak=default=default: notes173 = 173.applu: f90 -fast -O5 +PFB F77OPTIMIZE = -fast -O5 F77 = f90 fdo_post_make1 = <pixie.out 2>pixie.err mv oldexe.pixie ${baseexe} EOT fdo_post1 = spike oldexe -fb oldexe -stride_prefetch -o ${baseexe} 177.mesa=peak=default=default: notes177 = 177.mesa: cc -fast -O4 +CFB +IFB COPTIMIZE = -fast -O4 CC = cc fdo_pre0 = <pixie.out 2>pixie.err mv oldexe.pixie ${baseexe} EOT fdo_post1 = spike oldexe -fb oldexe -stride_prefetch -o ${baseexe} 183.equake=peak=default=default: notes183 = 183.equake: cc -fast -xtaso_short -assume notes183_1 = restricted_pointers -all -ldensemalloc -none +PFB COPTIMIZE = -fast -xtaso_short -assume restricted_pointers -all -ldensemalloc -none CC = cc fdo_post_make1 = <pixie.out 2>pixie.err mv oldexe.pixie ${baseexe} EOT fdo_post1 = spike oldexe -fb oldexe -stride_prefetch -o ${baseexe} 187.facerec=peak=default=default: notes187 = 187.facerec: f90 -fast -O4 +PFB FOPTIMIZE = -fast -O4 FC = f90 fdo_post_make1 = <pixie.out 2>pixie.err mv oldexe.pixie ${baseexe} EOT fdo_post1 = spike oldexe -fb oldexe -stride_prefetch -o ${baseexe} 188.ammp=peak=default=default: notes188 = 188.ammp: cc -fast -O4 -xtaso_short -assume notes188_1 = restricted_pointers COPTIMIZE = -fast -O4 -xtaso_short -assume restricted_pointers CC = cc 189.lucas=peak=default=default: notes189 = 189.lucas: kf90 -O5 -fkapargs='-ur=1' +PFB FOPTIMIZE = -O5 -fkapargs='-ur=1' FC = kf90 fdo_post_make1 = <pixie.out 2>pixie.err mv oldexe.pixie ${baseexe} EOT fdo_post1 = spike oldexe -fb oldexe -stride_prefetch -o ${baseexe} 191.fma3d=peak=default=default: notes191 = 191.fma3d: kf90 -O4 -transform_loops +PFB FOPTIMIZE = -O4 -transform_loops FC = kf90 fdo_post_make1 = <pixie.out 2>pixie.err mv oldexe.pixie ${baseexe} EOT fdo_post1 = spike oldexe -fb oldexe -stride_prefetch -o ${baseexe} 200.sixtrack=peak=default=default: notes200 = 200.sixtrack: f90 -fast -O5 -assume accuracy_sensitive notes200_1 = -notransform_loops +PFB F77OPTIMIZE = -fast -O5 -assume accuracy_sensitive -notransform_loops F77 = f90 fdo_post_make1 = <pixie.out 2>pixie.err mv oldexe.pixie ${baseexe} EOT fdo_post1 = spike oldexe -fb oldexe -stride_prefetch -o ${baseexe} 301.apsi=peak=default=default: notes301 = 301.apsi: kf90 -O5 -transform_loops -unroll 8 notes301_1 = -fkapargs='-ur=1' +PFB F77OPTIMIZE = -O5 -transform_loops -unroll 8 -fkapargs='-ur=1' F77 = kf90 fdo_post_make1 = <pixie.out 2>pixie.err mv oldexe.pixie ${baseexe} EOT fdo_post1 = spike oldexe -fb oldexe -stride_prefetch -o ${baseexe} ####################################################################### # Integer Portability # notes8xx are used for portability int=default=default=default: notes800 = notes801 = Portability: gcc: -Dalloca=__builtin_alloca; crafty: -DALPHA notes802 = perlbmk: -DSPEC_CPU2000_DUNIX; vortex: -DSPEC_CPU2000_LP64 notes803 = gap: -DSYS_HAS_CALLOC_PROTO -DSYS_IS_BSD -DSYS_HAS_IOCTL_PROTO notes804 = -DSPEC_CPU2000_LP64 176.gcc=default=default=default: EXTRA_CFLAGS= -Dalloca=__builtin_alloca 186.crafty=default=default=default: EXTRA_CFLAGS = -DALPHA 252.eon=default=default=default: CXXPORTABILITY = -lm 253.perlbmk=default=default=default: EXTRA_CFLAGS = -DSPEC_CPU2000_DUNIX 254.gap=default=default=default: EXTRA_CFLAGS = -DSYS_HAS_CALLOC_PROTO -DSYS_IS_BSD -DSYS_HAS_IOCTL_PROTO -DSPEC_CPU2000_LP64 255.vortex=default=default=default: EXTRA_CFLAGS = -DSPEC_CPU2000_LP64 ####################################################################### # Floating point Portability # notes8xx are used for portability fp=default=default=default: notes800 = notes801 = Portability: galgel: -fixed 178.galgel=default=default=default: EXTRA_FFLAGS = -fixed